How to Pick Out Roof Vent Lid for Snowmobile Trailer by Lightning Trailers

Question

Question:

Hello, I have a 2012 in line snowmobile trailer made by lightning trailers. The dome is cracked and needs to be replaced. There is no make or model on the vent that I can see. It is a 14x14 with an aluminum handle crank. The dome has a metal bracket that is riveted to the plastic dome. This bracket has a slot approximately 5-6” long in it to which an arm that is attached to the crank mechanism slides in to lift and close the dome. I will need the dome with the bracket attached if possible. Let me know if there is more info required. Thanks

asked by: Rick

0

Expert Reply:

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14".

To pick the correct cover, you will also need to know the type of hinge you need.

There is a 3 point hinge, such as the one on the Camco # CAM40153; a 4 point hinge as seen on the Camco # CAM40154; or a rolled metal continuous hinge like on the Ventline # BVD0449-A03; and universal hinge as shown on the MaxxAir # MA00-335001.

Basically the easiest way to select the correct replacement cover is to remove the existing cover and match the hinge and lift bracket to the photos on our site along with the dimensions. A link to all of the replacement vent covers is provided to match up with your cover.

If it is not clear which hinge style that you have, the MaxxAir above is a Universal Replacement Lid.

In the event that you don't find a lid you like, I also included a link to our main page for our complete 14 x 14-inch vent assemblies. These are offered in manual or powered lift and with or without fans. If you install a complete new vent you'll need an installation kit, either # 344270KITW for a metal or coated metal roof or kit # CAM25013 for a rubberized roof.

expert reply by: Jameson C

0

click to enlarge

Answer 1

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 2

For your 3,500 lb Dexter Torsion axles, you will want to use the Torflex Lift Kit - Tandem Axle - 2-5/8" Lift #K71-707-02. This will provide an additional 2-5/8" clearance. The distance between the mounting bolts is 8 inches center on…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The best hitch for a 2024 Subaru Outback is the etrailer item #e25TR. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver, that has a 3,500 lbs towing capacity and a 350 lbs…

view full answer...

Answer 5

Congrats on the new car! For your 2024 Subaru Outback, I recommend the etrailer Hitch item #e25TR. This hitch is custom fit and bolts to your Subaru with included hardware. I really like this hitch because it mounts behind the rear bumper cover…

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 8

Thanks for passing that on! I attached the install video for the #C56040 on the 23 Outback you mentioned as well.

view full answer...

Answer 9

Yes, the Draw Tite hitch part #DT73RR does fit the 2024 Subaru Outback Touring XT as it fits all 24' models. It's pretty common to have to lower the exhaust for hitch installs as well.

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

For your 2023 Subaru Outback, I recommend the Curt Trailer Hitch item #C69VV. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver. I really like this hitch because it is an easy…

view full answer...

Answer 12

The Curt Trailer Hitch Receiver #C69VV does fit the 2024 Subaru Outback Wilderness. Ground clearance will be further reduced at the rear compared to other hitches for the Outback since it has a visible cross tube. Bumper removal is not required, but…

view full answer...

How to Pick Out Roof Vent Lid for Snowmobile Trailer by Lightning Trailers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching