What Are Landing Gear Legs For 2014 2014 Keystone Cougar 327 RES

Question

Question:

What brand of landing gear on my 2014 cougar 327 res??

asked by: Jim

0

Expert Reply:

There are a few possibilities but more than likely they are Lippert Components because they supply most of the OEM legs for RV manufacturers. If you need to replace your legs then the Lippert Landing Gear Set, Item # LC333964, is a good option. If the distance from outside to outside of your landing gear brackets are 17-1/2 inches then these will fit. If not, you may have to find a qualified welder to move your brackets so that everything matches up.

expert reply by: Brint H

0

click to enlarge

Answer 1

No grease or lubrication is necessary to maintain the Lippert Components Camper Jack #LC333964. According to Lippert, the only maintenance for the camper jack is to wash the jack with mild soap and water. This would be advisable after traveling in…

view full answer...

Answer 2

Lippert makes most of the OEM legs for RV manufacturers. Several customers have replaced their fifth wheel legs with the Lippert Landing Gear Set, Item #LC333964. Depending on your brackets, you may have to find a qualified welder to move them so…

view full answer...

Answer 3

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if…

view full answer...

Answer 4

I have some really great options for complete landing gear sets to use on a Forest River Cardinal Fifth Wheel, the Landing Gear Set with Handle part #RVLG-8HDL for example is super cost effective and it comes with everything you need. In regards to…

view full answer...

Answer 5

Your Raptor Toy Hauler likely has a landing gear setup similar to the one you were looking at: Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs #LC333964. If so, then the correct replacement motor would be Lippert…

view full answer...

Answer 6

Take the top off of the jack leg and inspect the bevel gears that you can see. If they look damaged all you'd need is the repair kit part #LC146060. If other components look damaged it would be best to replace the entire leg with part…

view full answer...

Answer 7

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

view full answer...

Answer 8

In order to pick out a direct replacement for the landing gear on your 2001 sunnybrook 31bwfs we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder…

view full answer...

Answer 9

If the brand of landing gear you have now on your Keystone Laredo is a Ram brand then yes you could reuse it's motor with the #RVLG-8HDL. But most likely you have a Lippert set of landing gear based on what typically they used so instead the part…

view full answer...

Answer 10

You are right on the money with the differences between the two etrailer landing gear sets; the only difference is that one comes with the manual hand crank (handle) and the other does not: - Manual Hand Crank: Landing Gear Set with Handle -…

view full answer...

Answer 11

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 12

I went out to our warehouse so I could take a couple measurements on the etrailer.com Landing Gear Set #RVLG-8000 referenced in your question. From the center of the cross shaft to the bottom of the top weld stop I measured a distance of right at 7…

view full answer...