Are the Inside Corners of the Ceiling Garnish # FVK1060-81 Round or Square

Question

Question:

Does that vent garnish ring have square inside corners or does it have rounded corners?

asked by: Cody C

0

Expert Reply:

I attached a picture that shows the inside corners of the Ceiling Garnish # FVK1060-81 that you referenced to show you how round or square they are.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The trim ring you are referencing is called a ceiling garnish. There are different colors and different depths with the ability to cut them to custom height. I've linked the page to your options to assist. All of them are 1-1/2 inches on each…

view full answer...

Answer 2

The Off White Ceiling Garnish #FVK1060-80 will fit your application perfectly. It has the 6" leg that you'll need to cut down to fit your 5-1/4" application but aside from that everything else will match up perfectly. If you need a…

view full answer...

Answer 3

The roof vent dimensions of 14" x 14" or 14-1/4" x 14-1/4" are an industry standard. I would say around 95% (if not more) of all roof vents follow these standard dimension. The variances you are seeing most likely have to do with…

view full answer...

Answer 4

I reached out to my contact at Fan-Tastic Vent and he said that if your model 1200 roof vent is under 5 years old then they know for a fact that the Ceiling Garnish #FVK1060-81 will fit. The company who previously owned Fan-Tastic Vent didn't…

view full answer...

Answer 5

Yes, the Ceiling Garnish for Fan-Tastic Vents Roof Vent #FVK1060-81 that you referenced will replace your Fantastic Vent Create-A-Breeze interior garnish part #8060 as it is also 6 inches deep and matches the other dimensions needed as well.

view full answer...

Answer 6

First, the Coach Steps need to operate off of a fully charged battery. A drop in voltage can cause malfunctions. Once you are certain the battery is fully charged you can follow the steps below to troubleshoot the Coach Step: 1. Disconnect the plug…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

Hey Colin, we do have the lift arm with part #FVK8014-05 but the only replacement lids we offer are the domed ones like #FVK1020-19.

view full answer...

Are the Inside Corners of the Ceiling Garnish # FVK1060-81 Round or Square

Product Page this Question was Asked From

Continue Researching