Replacement Roof Vent Garnish For Fantastic Vent Create-A-Breeze

Question

Question:

Will Part Number FVK1060-81 replace a Fantastic Vent Create-A-Breeze interior garnish part # 8060? The information that I found for the vent stated that the garnish was 6inch deep.

asked by: James H

1

Helpful Expert Reply:

Yes, the Ceiling Garnish for Fan-Tastic Vents Roof Vent # FVK1060-81 that you referenced will replace your Fantastic Vent Create-A-Breeze interior garnish part # 8060 as it is also 6 inches deep and matches the other dimensions needed as well.

expert reply by: Jameson C

1

Answer 1

I attached a picture that shows the inside corners of the Ceiling Garnish #FVK1060-81 that you referenced to show you how round or square they are.

view full answer...

Answer 2

First, the Coach Steps need to operate off of a fully charged battery. A drop in voltage can cause malfunctions. Once you are certain the battery is fully charged you can follow the steps below to troubleshoot the Coach Step: 1. Disconnect the plug…

view full answer...

Answer 3

We may have a solution available for you though we do not have a list of individual parts for specific trailers. However, you will likely find something that works, such as the Global Link RV Entry Door Locking Latch Kit #295-000019, which is a…

view full answer...

Answer 4

The opening on your snowmobile trailer is most likely 14-1/4" x 14-1/4" as that is the standard size that nearly all newer trailers on the market use. In order to find the correct one for you we would need to know what type of hinge you…

view full answer...

Answer 5

You certainly can replace your tub with a shower in your travel trailer. This would be the same as if you were swapping out the tub in your home for a shower. I have linked our selection of shower pans for you to filter through but you will need to…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Colin, we do have the lift arm with part #FVK8014-05 but the only replacement lids we offer are the domed ones like #FVK1020-19.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 12

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Replacement Roof Vent Garnish For Fantastic Vent Create-A-Breeze

Product Page this Question was Asked From

Continue Researching