Does etrailer.com Trailer Hub part # AKIHUB-440-2-1K Fit with 12 inch Diameter Trailer Wheel

Question

Question:

On the 4x4 hubs, want to make sure I get the 4x4 hubs that support the larger 12inch 4.8-12 via the hub pilot diameter being different than the 8inch wheels. Dont seem to see the pilot hub dims on the 4 on 4 idle hub pages?

asked by: Ryan

0

Expert Reply:

The trailer hub part # AKIHUB-440-2-1K that you referenced has a mounting flange and snout diameter that is compatible with 12 inch trailer wheels like you said you were needing.

expert reply by: Jameson C

0

Answer 1

If you're looking for a pre-greased trailer hub assembly to match bearing number #L44643 you can use this trailer hub assembly #AKIHUB-440-2-1K which comes with L44643 bearings that are pre-greased. I've included a review video for this hub…

view full answer...

Answer 2

Trailer Idler Hub Assembly #AKIHUB-440-2-1K uses two of bearing part #L44643 which fit on a 0.99-inch diameter spindle. I went to our warehouse to measure this hub for you. The overall exterior depth of the hub from end to end (see picture please) is…

view full answer...

Answer 3

Since your inner and outer bearing surfaces measure .99 inch in diameter and the seal diameter is 1.24 inch you do have a BT8 spindle. The bearing kit we have for this spindle and the hub it's designed for is the part #BK1-100. The bearing, race,…

view full answer...

Answer 4

I would love to help but the manufacturer doesn't provide us with any dimensional drawing of the Trailer Idler Hub Assembly for 2,000-lb Axles part #AKIHUB-440-2-1K. However, I went out to our warehouse for you and took a few useful measurements.…

view full answer...

Answer 5

The best way to match hubs to an axle/spindle is going to be by finding a hub with the same size bearings as the ones that you removed; you can usually find numbers stamped on the backs of the bearings that designate their size. The Trailer Idler Hub…

view full answer...

Answer 6

Your pictures didn't come through but we do have some hubs that use the same #L44643 bearings. The etrailer.com Hub Assembly #AKIHUB-440-2-1K uses those same bearings and #L44610 races that you mentioned. It also uses a grease seal that has a…

view full answer...

Answer 7

The Trailer Hub part #AKIHUB-440-2-1K that you referenced is designed to fit a BT8 spindle like the part #TRU94FR which has an overall length of 8-1/4 inches and a stub length of 3-3/8 inches. That means the remaining section where the seal,…

view full answer...

Answer 8

The two bearings you mentioned have different inner diameters. The #L44643 has an inner diameter that is exactly 1 inch and the #L44649 is 1.06 inch. This may not seem like a lot but it's a big enough difference to prevent the hub you have now…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

Yes, the BT8 Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter #TRU94FR and the Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased #AKIHUB-440-2-1K are compatible with each other.

view full answer...

Answer 11

The trailer hub part #AKIHUB-440-2-1K matches exactly what you would need. Bearings, bolt pattern and stud dimensions are the exact same.

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Does etrailer.com Trailer Hub part # AKIHUB-440-2-1K Fit with 12 inch Diameter Trailer Wheel

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching