Install Instructions for Reese Universal Fifth Wheel Rail Kit in 2004 GMC Sierra 2500HD

Question

Question:

I have a GMC Sierra HD2500 SLE Short Box would love the install instructions Thank you and have a great day

asked by: Robert S

0

Expert Reply:

I attached the instructions for the # RP30035 that are specific to your 2004 GMC Sierra 2500 in a picture on this page.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The info on your Putnam Hawkeye is actually pretty hard to come by since they've been out of business for so long but there's one measurement you can take to determine if it will fit into the Curt Rail Kit part #C16200 that you referenced.…

view full answer...

Answer 2

I have attached the complete installation instructions for the Reese Universal Base Rails and Installation Kit #RP30035 that is included with the Pro Series Sliding Hitch #PS30129. This is a universal rail kit that is designed to fit most trucks. You…

view full answer...

Answer 3

It sounds like you are asking how far apart the above bed base rails need to be spaced to use the Curt A20 #C16541. If that is the case then the above bed base rails will need to be spaced 22" apart front to back on center. This measurement is…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Install Instructions for Reese Universal Fifth Wheel Rail Kit in 2004 GMC Sierra 2500HD

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching