1-1/2 inch Valterra Bladex Waste Valve Recommendation for 1-1/2 inch Gray Water Tank Valve

Question

Question:

Regarding Valterra EZ Valve Electric Waste Valve for RV Black Water Tank - 3inch Diameter Item # E1003VP. I will be installing on my grey tank which is 1 1/2 inches. Which adapter would I need and do you have it in stock? Thanks

asked by: Dan P

0

Expert Reply:

Since you have a 1-1/2 inch gray water tank valve what you'd want is the part # T1001VP for that size. We don't have an electric version of this though.

expert reply by: Jameson C

0

Answer 1

The abs cement isn't going to come loose and will require you to cut the pipe a bit further back and using a coupling #D50-2935 and more straight pipe to get back to where it originally sat for the valve. That being said, you can also just unbolt…

view full answer...

Answer 2

To widen your 1-1/2" pipe to 3" using the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub #T1041-1 you would first need the Valterra DWV Adapter for RV Sewer System - ABS Plastic - 1-1/2" Hub to FPT…

view full answer...

Answer 3

From what I can gather it sounds to me like you need the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub #T1041-1. The 3" Spigot mounts directly in the gray water tank outlet while the 1-1/2" Hub slides…

view full answer...

Answer 4

You could probably extend the wires individually of the Valterra EZ Valve Electric Waste Valve for RV Black Water Tank #E1003VP but we don't an extension harness made specifically for this.

view full answer...

Answer 5

Valterra EZ Valve Electric Waste Valve #E1003VP is operated with a switch and the valve would either open or close accordingly. If you are talking about just installing a second switch then it is possible though the switch is not available…

view full answer...

Answer 6

The difference between a hub connection and a spigot connection is that the hub is the female end and has a lip on the inside that stops the spigot (or male) end where it needs to be. I have attached some pictures to assist. With this knowledge it is…

view full answer...

Answer 7

This is a pretty common issue as the 12 volt accessory/charge circuit is not always active on vehicles with OEM 7-ways. The solution is to run 10 gauge wire like part #10-1-1 (sold by the foot) through a breaker like part #9510 between the 1:00 pin…

view full answer...

Answer 8

To make your life easier you could just remove the center section of your current waste valve and then install just the center section of the part #E40B-8 so that you can convert to an electric setup without having to deal with a much more involved…

view full answer...

Answer 9

Yes you are correct Valterra EZ Valve Electric Waste Valve for RV Black Water Tank part #E1003VP does come with everything you will need. The confusion came from the spigot or hub ends and which one they needed for their application in that question.…

view full answer...

Answer 10

In order to help prevent leaking between the grommet and tank on the Replacement Rubber Grommet for RV Black Water Tanks part #F02-2106 it would be wise to use a sealant like part #LT37467 between the two surfaces. I am not sure if this is a…

view full answer...

Answer 11

When you install a Solera awning arm kit like the part #LC434724 that you referenced you need to wind the awning 14 times so that it has the correct amount of spring tension. Now this isn't a dangerous level of tension like what you might see…

view full answer...

Answer 12

If the fabric on your Solera RV Slide-Out Awning - 6'7" Wide - 48" Projection - White #LCV000163285 is laying loose with no tension you've most likely lost the required amount of tension on your tension springs. You'll want to…

view full answer...

1-1/2 inch Valterra Bladex Waste Valve Recommendation for 1-1/2 inch Gray Water Tank Valve

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching