Replacement Leg for Ground Control 3.0 Automatic Leveling System

Question

Question:

The internal screw shaft broke at the top where the pin goes through it. It is brand new, what is the part number for that?

asked by: Jerry C

0

Expert Reply:

There are not replacement internal parts for the Ground Control System. You will need to replace the whole leg. We offer both Left # LC305339 and Right # LC344792 rear legs as well as the Lead leg # LC305340 for either front leg replacement.

Since you mentioned that it is brand new, it may be covered under Lippert Warranty. I recommend contacting the manufacturer if it is within the 1 year warranty of the # LC358590 system. I haven't seen this issue before, so it may be a one-off manufacturing defect.

expert reply by: Jason S

0

click to enlarge

Answer 1

I checked the parts list for the Ground Control 3.0 Electric Leveling System #LC358590 (4-Point Set) or #LC675817 (6-Point Set) and the jack tube by itself is not available as a replacement part. Due to that if you need a replacement leg you will…

view full answer...

Answer 2

When it comes to replacing your snap pads for your 9 inch round Lippert Ground Control 3.0 on your 2021 Keystone Laredo The SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 4 #SP54FR4 is what you need. They will…

view full answer...

Answer 3

Thanks so much for the photo, it was very helpful. Based on that the correct replacement leg for the Lippert Ground Control 3.0 Electric Leveling System #LC358590 on your Keystone Cougar is actually going to be the Replacement Left Rear Leg…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Hey Tim, thanks for reaching out! The Stromberg Carlson Base Pad Extreme for RVs and Trailers #SC33VR have a 6,000 lb rating for each Base Pad Extreme so you're looking at a total of 36,000 lbs for this kit of 6. Ideally your jacks will have the…

view full answer...

Answer 6

SnapPads like the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 6 Item #SP54FR6 can be taken off and on as needed so you won't have to keep replacing them every time you need to take them off.

view full answer...

Answer 7

If you have the Gooseneck versions of the Curt CrossWing ( #C92DR or #C32DR) you unfortunately would not be able to use the Rota-Flex with it. The pivoting head causing too much strain for the single point of contact you have with a gooseneck hitch.…

view full answer...

Answer 8

I am sorry but we do not have an AC cover with those dimensions. The closest option we have is the Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners item #AT3308046006 which measures 40-1/2" long x 29" wide x…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The SnapPad Prime Jack Pads #SP84FR4 are specifically designed to fit the Power Gear Leveling Systems w/ 10" Round Concave Jack Feet on your 2014 Fleetwood Bounder 34B. The Pads #SC99MR Stromberg told you to use will not fit on your Bounder as…

view full answer...