Will Ultra-Fab Rotating, Hitch Mounted Skid Wheels # UF48-979014 Fit a 3-1/2 Inch Square Bumper

Question

Question:

I have aftermarket back bumper made from 3.5inch square metal tubing. Looks like this might fit if I used the longer dimension 4.5 will this work?

asked by: James

1

Helpful Expert Reply:

At most you might need different hardware but other than that you could use Ultra-Fab Rotating, Hitch Mounted Skid Wheels # UF48-979014. I have also included a link to our skid wheel options for you.

expert reply by: Michael H

1

Answer 1

I suggest skid wheels, such as the Ultra-Fab Rotating, Hitch Mounted Skid Wheels, #UF48-979014. Attach this to the frame not the prop guard. See images and please note the link below to our full selection.

view full answer...

Answer 2

I went out to the warehouse and pulled the Ultra-Fab Rotating, Hitch Mounted Skid Wheels for RVs, part #UF48-979014, and took some measurements for you. See the image I made for you elsewhere on the page. The bolt holes measure 3-1/2" long and…

view full answer...

Answer 3

The hardware that comes with the Ultra Fab Skid Wheels part #UF48-979014 is not going to directly fit around a 3 inch by 3 inch beam but you could have the hardware welded to the beam instead and it would work great.

view full answer...

Answer 4

We do not have a set of roller that attaches directly to the V-skids of a trailer, but the Ultra-Fab Rotating, Hitch Mounted Skid Wheels #UF48-979014 will sit 5-3/4 inches below where they are attached to so they may hang below the skids of your…

view full answer...

Answer 5

I pulled a Ultra-Fab Rotating, Hitch Mounted Skid Wheel #UF48-979014 from our warehouse to measure the dimensions of the top plate and found that it measures 4-1/2 in length by 3-7/8 inches in width. I attached a picture and video that shows these…

view full answer...

Answer 6

Installing skid wheels on your new 16 foot travel trailer, such as the Ultra-Fab Skid Wheels #UF48-979011, will not cause any damage to its frame or overall structure. These are designed specifically to help with the issue you are having when going…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...