Difference Between Hopkins Breakaway Battery Kits HM20001 and 20099

Question

Question:

what are the differences in item number: HM2001 vs. 20099? thanks

asked by: Brad S

0

Expert Reply:

The big difference between the Hopkins Engager breakaway kits is that the # HM20001 does not have a charge status display on the lid like the part # 20099 does. The # 20099 allows you to press a button and know what the charge of the battery is like.

expert reply by: Jameson C

0

Answer 1

The Optronics light, part #MC48RB, and the Optronics light, part #MC48AB, are the red and amber equivalent lights to the Bargman part #34-68-511 and part #30-68-511.

view full answer...

Answer 2

Pretty much the only difference between the Engager breakaway systems #20099 and #20400 are the designs of the battery boxes. Both function the same and have the same features. Engager #20400 is meant to be mounted to the side of the trailer frame…

view full answer...

Answer 3

The difference is the length of the lead wire. Both part #20099 and (discontinued) part #HM20119 use the same Engager Push-To-Test Trailer Breakaway Kit w/ Built-In Charger but the part 20099 only has a 7" long lead wire while part 20119 has a…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 6

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Difference Between Hopkins Breakaway Battery Kits HM20001 and 20099

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching