Front Hitch Recommendation for 2012 Ford F-450 Winnebago RV

Question

Question:

Need front rcvr hitch. Is this the correct one? Thanks

asked by: Tom C

1

Helpful Expert Reply:

There is a front-mounted hitch that is a fit for your 2012 Winnebago built on a Ford E-450 chassis, the Draw-Tite # 65053. It is a bolt-on installation that comes with the necessary hardware for install.

expert reply by: Jameson C

1

click to enlarge

Answer 1

For your 2011 Ford E-450 Cutaway RV frame the Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2" #65053 is the correct front mounted hitch. This is a simple bolt on assembly that is estimated to take about 1-1/2 hours to complete. It…

view full answer...

Answer 2

Line pull for a front hitch like the Draw Tite part #65053 is basically the rolling weight capacity of what it could move without the presence of an incline. So if you have a rolling load on level ground pulled straight (no side-to-side angling) to…

view full answer...

Answer 3

The Lionshead Steel Dual Wheel, 4.75" Pilot - Silver, Item #LHHA420 is a 16" x 6" wheel with an 8 on 6-1/2 bolt pattern, so as long as your Class C motorhome wheels have the same bolt pattern and are the same 16" x 6"…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 6

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Front Hitch Recommendation for 2012 Ford F-450 Winnebago RV

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching