Distance Between Mounting Holes of Carr Custom-Fit Side Step # CARR103991

Question

Question:

What is the distance between holes that secures step to vehicle?

asked by: Guy K

0

Expert Reply:

The distance between the two mounting holes on the mounting bracket for the part # CARR103991-1 is 1.9 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The distance between the mounting brackets of the CARR Side Steps #CARR103991-1 that you referenced is 8-1/2 inches on center.

view full answer...

Answer 2

I went out to our warehouse and measured the: -Replacement Mounting Brackets for Carr Custom-Fit Side Step #CARRBR14702K2, and was able to get the following dimensions for you: -Overall Height - 3-7/8", -Bracket Height At Bend - 3-1/4",…

view full answer...

Answer 3

The Carr #CARR103991 hoop steps are a confirmed fit for your vehicle. For both the front and rear doors, you'll need two sets of steps. The steps attach to the vehicle by bolts that run through the body pinch weld and screws into the rocker…

view full answer...

Answer 4

The Carr Custom-Fit Side Steps - Hoop II - Black Powder Coated Aluminum - 7" Step - 1 Pair #CARR103991 have a measurement of 1.9 inches vertically and 8.5 inches horizontally measuring hole center on center. I've attached a photo to assist.

view full answer...

Answer 5

The Bully Black Bull Side Steps - Aluminum - Matte Black - 7" Step - 1 Pair #BBS-1103 is 7 inches long x 3-5/8 inches wide. The height from your pinch weld on your vehicle to the top of the step will depend on how you mount the step but you can…

view full answer...

Answer 6

If you were to install the CARR steps #CARR103991-1 on your 2010 GMC Sierra they would stick out 8-5/8 inches from where they are installed.

view full answer...

Answer 7

The Carr Custom-Fit Side Step #CARR103991-1 referenced in your question does include all the necessary hardware for installing the step on your truck. The step platform is 7 inches long and 3-1/2 inches wide. This will come with 1 step and a limited…

view full answer...

Answer 8

I reached out to Carr and found that the plate that you step on on the #CARR103991-1 is 1/4" thick.

view full answer...

Answer 9

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 10

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Distance Between Mounting Holes of Carr Custom-Fit Side Step # CARR103991

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching