A-Frame Jack Recommendation for Jayco Trailer that Needs 2 inch Outer Tube Diameter

Question

Question:

Hi, I ordered a trailer jack from you guys, but the outside tube diameter is 2 1/4, which is too big for my Jayco popup. The opening for the tube is 2. What would you recommend for a jack with a 2inch outside tube diameter? Thanks,

asked by: Dan O

0

Expert Reply:

The diameter of the outer tube of the Jack part # DL22530 that you referenced is 2 inches. the diameter of the inner tube is 1-3/4 inches.

Most jacks have a slightly larger outer tube at 2-1/4 inches.

I attached an install video for this jack for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I have good news, our trailer jack that has a 2 inch outer diameter part #DL74MR would fit and work well. While it has a 1,000 lb weight capacity that does not mean 1,000 lb total trailer weight capacity. That capacity is the tongue weight capacity…

view full answer...

Answer 2

Given the 3500 lb weight of your trailer, your tongue weight will be somewhere between 350 and 525 lbs, so you won't need a jack with a super-high capacity. This being said, choosing a jack with a higher rating than you need isn't a bad idea.…

view full answer...

Answer 3

For the Dutton Lainson trailer jack part #DL22530 that you referenced we have the replacement wheel part #DL22414.

view full answer...

Answer 4

I do have an option for you but the Ultimate Trailer Jack part #322-RDJ-2K only comes with an outer diameter of 2-1/4". The 2" outer diameter tube jacks are harder to find. We do have the A-Frame Trailer Jack - Sidewind - 1,000 lbs. by…

view full answer...

Answer 5

The Dutton Lainson Trailer Jack #DL22530 that you referenced would work great for your application as its outer tubing diameter is 2 inch so it would fit perfectly in the 2 inch opening you have now. For more info on this USA made jack check out the…

view full answer...

Answer 6

I think you are asking about a trailer jack for your Jayco popup. If so we have just what you need. For an a-frame camper I recommend a jack like part #TJA-5000S-B. This is a sidewind jack that has a 5,000-lb capacity and has a 15-5/8 inch lift. This…

view full answer...

Answer 7

I will assume you are looking for an A-frame mounted jack, because that is what pop-ups typically use, and because that is the part you referred to. The bolt hole pattern is standard, so matching up with the holes in the trailer tongue should not be…

view full answer...

Answer 8

The 2-1/4" opening is the standard for the A-Frame jacks. Your particular opening may appear different due to rust buildup over the years. I see a lot of these trailers switch over to a bolt on side mount jack due to being easier to access and…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

A-Frame Jack Recommendation for Jayco Trailer that Needs 2 inch Outer Tube Diameter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching