Hitch Pin Lock Recommendation for Swagman 1-1/4 inch Hitch Bike Rack

Question

Question:

"will this work for swagman bike rack application for a 1-1/4" threaded receiver bar ..?

asked by: Troy

0

Expert Reply:

For a Swagman 1-1/4 inch hitch bike rack you would want the part # S64029 and not the # F-315 which would not fit.

expert reply by: Jameson C

0

Answer 1

The Replacement Threaded Hitch Bolt #05002400000 you were looking at is 3-5/16" long and is 1/2" x 13 course thread. This bolt is designed for SportRack bike racks and cargo carriers, and is not a confirmed fit for your Swiss Cargo Bike…

view full answer...

Answer 2

The Swagman Replacement Threaded Hitch Pin and Clip #P5901 is designed to fit Swagman bikes racks with 2 inch shanks. This hitch pin has an outer diameter of 5/8 inch. If your bike rack has a 1-1/4 inch shank then you will want to use #P5902. This…

view full answer...

Answer 3

According to Swagman, their #S64029 locking hitch pin uses a 1/2 inch coarse threaded bolt. We don't carry Bell bike racks, so I can't test it for you or guarantee fit.

view full answer...

Answer 4

The Thule Snug Tite Hitch Lock and Anti-Rattle Device, #THSTL2, can only be used on Thule brand bike racks. Most bike rack manufacturers will only design the hitch locks to only fit their products. The threads are unique to the manufacturers bike…

view full answer...

Answer 5

You wouldn't want to use a thread locker with the hitch pin lock #F-315. When torqued properly it won't back off and a thread locker would make the bolt much harder to remove when you needed to take it off.

view full answer...

Answer 6

I went out into our warehouse and measured the threads of the Replacement Threaded Hitch Pin and Clip #P5902 and found them to be 1/2 inch diameter coarse thread. The version of this bolt that is designed for 2 inch hitches is the Swagman Threaded…

view full answer...

Answer 7

We do not carry the Allen brand of bike racks but we do offer some anti-rattle options that may work for your needs but this is going to depend on how the bike rack pin hole and shank are configured. If the pin hole on your bike rack is not threaded,…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You are on the right track. The only way we have that will allow you to use the Thule T2 Pro Xtr Bike Platform Rack part #TH69TX with the 2.5" receiver tube opening on your truck would be with adapter. For this, I recommend the Brophy Hitch…

view full answer...

Answer 11

To keep your back end from squatting, I recommend the Coil SumoSprings Custom Helper Springs for Coil Spring Suspension item #CSS-1094R. These insert into your rear springs and keep your suspension from being pushed down by the weight of your…

view full answer...

Answer 12

I recommend the Roadmaster Dual Hitch Receiver Adapter, 10" Drop/Rise item #RM-077-10. This adapter was designed for this type of set up. Your Jeep Rubicon and Swagman E bike rack weigh well below the 10,000 lbs maximum capacity of this hitch. I…

view full answer...