What Size Threads are Used on the Replacement Threaded Hitch Pin and Clip # P5902

Question

Question:

I am looking for a longer pin. My 3/4 ton truck has a wider receiver than a normal 2, and the pin is short. How can I get or make a longer pin? I need to know the thread size, in order make or buy one.

asked by: Bob K

0

Expert Reply:

I went out into our warehouse and measured the threads of the Replacement Threaded Hitch Pin and Clip # P5902 and found them to be 1/2 inch diameter coarse thread. The version of this bolt that is designed for 2 inch hitches is the Swagman Threaded Hitch Pin part # P5901. This will not fit on 1-1/4 inch shank Swagman racks with 2 inch adapter sleeves though.

expert reply by: Jameson C

0

Answer 1

The Replacement Threaded Hitch Bolt #05002400000 you were looking at is 3-5/16" long and is 1/2" x 13 course thread. This bolt is designed for SportRack bike racks and cargo carriers, and is not a confirmed fit for your Swiss Cargo…

view full answer...

Answer 2

For a Swagman 1-1/4 inch hitch bike rack you would want the part #S64029 and not the #F-315 which would not fit.

view full answer...

Answer 3

The Thule Snug Tite Hitch Lock and Anti-Rattle Device, #THSTL2, can only be used on Thule brand bike racks. Most bike rack manufacturers will only design the hitch locks to only fit their products. The threads are unique to the manufacturers bike…

view full answer...

Answer 4

We do not carry the Allen brand of bike racks but we do offer some anti-rattle options that may work for your needs but this is going to depend on how the bike rack pin hole and shank are configured. If the pin hole on your bike rack is not…

view full answer...

Answer 5

According to Swagman, their #S64029 locking hitch pin uses a 1/2 inch coarse threaded bolt. We don't carry Bell bike racks, so I can't test it for you or guarantee fit.

view full answer...

Answer 6

The Swagman Replacement Threaded Hitch Pin and Clip #P5901 is designed to fit Swagman bikes racks with 2 inch shanks. This hitch pin has an outer diameter of 5/8 inch. If your bike rack has a 1-1/4 inch shank then you will want to use #P5902. This…

view full answer...

Answer 7

You wouldn't want to use a thread locker with the hitch pin lock #F-315. When torqued properly it won't back off and a thread locker would make the bolt much harder to remove when you needed to take it off.

view full answer...

Answer 8

Both of the bolts that come with the Yakima Hitch Pin Set #Y8880131 are 1/2 inch diameter with 13 threads per inch. One is 4.279” long and the other is 2.598” long.

view full answer...

Answer 9

The Yakima Threaded Hitch Bolt, part #Y8890200 is 5/8 inch in diameter and a 4-1/4 inch overall length, as shown in the provided photo. The StickUp originally included two different hitch bolts, one for the 2 inch hitch and a shorter one for the…

view full answer...

Answer 10

You can use clip part #AM3427 for your Swagman XTC-2 bike rack #S64670. This is a general-purpose part that fits multiple applications.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...