Wire Color Functions on the Hopkins 5th Wheel/Gooseneck Wiring Harness Part # 41157

Question

Question:

What does each color do green is right yellow is left brown is tail lights I’m modifying it to use on my 04 ram just need to know Purple Blue White Red

asked by: JJ

0

Expert Reply:

In regards to the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness with 7-Pole Plug part # 41157:

Purple - Reverse/Backup Light (Center Pin)

Blue - Brake Controller Output (5 O'Clock Pin)

White - Ground (7 O'Clock Pin)

Red - +12 Volt Power (2 O'Clock Pin)

You can see a photo of how the wire color relates to the pin positions below.

expert reply by: Conner L

0

click to enlarge

Answer 1

The Brophy camper tie downs #HSAB are pretty universal and should fit your 1997 Chevy K1500 pretty easily but you might measure the bed rails just to be sure. As long as you have 2 inches of space between the lip of the bed rails and the side of…

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 3

The only pin that should be continuously showing 12V power on the 7-Way connector on your vehicle is the 12V power circuit which is normally the black wire but not always. In 7-way wiring the 12V auxiliary power feed is carried on the contact at…

view full answer...

Answer 4

Generally you see this situation on a vehicle that has LED lights because there is a power bleed coming from a different circuit into the lighting circuit. LED lights require a lot less power than incandescents, that's one of the biggest…

view full answer...

Answer 5

Somewhere in the wiring the turn signal wire(s) is touching the running light wire. This is likely happening closer to the front of the trailer, perhaps at the connector but I would not rule out a short anywhere from the front to the back. Also, by…

view full answer...

Answer 6

The HSSF hold down brackets would use the Tie Down Hardware Package, part #TDHP, which includes hooks, chain and turnbuckles. The tie down hardware would typically attach to existing eye bolts built into the underside of camper. If your camper does…

view full answer...

Answer 7

The Camper Hold Downs, #HSSF, are a universal fit item that will fit most full size trucks. This should include your 1969 Ford F-250. In order to be sure, take a look at the last 2 pictures on the product page. These pictures show the dimensions of…

view full answer...

Answer 8

I spoke with my contact at Brophy and they stated you'll be fine using the Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item #HSWB as long as the railing on the back of your 2008 Chevy Silverado…

view full answer...

Answer 9

Brophy recommends using their rigid tie down hardware kit, part #TDHP, as their tie downs provide a small amount of flex.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Wire Color Functions on the Hopkins 5th Wheel/Gooseneck Wiring Harness Part # 41157

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching