Does Trailer Hitch 36540 Require any Welding to Install on Toyota Camry

Question

Question:

Does hitch have to be welded on

asked by: Saundra L

0

Expert Reply:

The Draw Tite hitch part # 36540 that you referenced is designed to be bolted to the frame of a newer Toyota Camry and does not require any welding at all.

I attached an install video for this hitch on a 2016 Toyota Camry for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

In my opinion you are going in the right direction with a frame mounted receiver. The only advantage to a weld on application is that, if welded properly, the attachment point, weld, will be stronger than the hitch or trailer frame steel and one of…

view full answer...

Answer 3

The Curt hitch, part #C12107 for your 2017 Toyota Camry V6 does require some modifications but at least most of it isn't visible. The heat shield above the exhaust needs some minor trimming which you can see in the video I attached at around the…

view full answer...

Answer 4

The only hitches available for the 2014 Toyota Camry are class II with a 1-1/4" receiver. The best option is the Curt Trailer Hitch item #C12107. This hitch is custom fit and bolts to your Camry with included hardware. It has a 200 lbs tongue…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 12

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Does Trailer Hitch 36540 Require any Welding to Install on Toyota Camry

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching