Fit of Electric Stabilizer Jack LC298707

Question

Question:

Can you show a picture of the attachment method and will it fit a 71 frame width? Trailer is a 2016 Coachmen Apex any attachment info would be great.

asked by: Rich S

0

Expert Reply:

In terms of fit, the Lippert Components Power Stabilizer Jack # LC298707 requires mounting hole spacing (center to center) of 68-11/16".

expert reply by: Kyle S

0

Answer 1

That's a good question and we do have an option for you to level your camper, but for that you'll need something to go with the Lippert Scissor Stabilizer Jacks #LC285326. Scissor jacks are only meant to stabilize and aren't designed or…

view full answer...

Answer 2

I highly recommend going with the Lippert Components High-Speed Power Stabilizer Jack #LC298707. An electric stabilizer is the best option because of the convenience it offers compared to manual stabilizers; this jack comes with a waterproof switch…

view full answer...

Answer 3

Typically around the motor area of the stabilizer jack there will be a label that will have part numbers and other info listed. I attached a picture of what it looks like on the #LC298707 that you referenced. Lippert does sometimes use alternate part…

view full answer...

Answer 4

The physical weight of the Lippert Components High-Speed Power Stabilizer Jack part #LC298707 is around 65 lbs. However, if you were instead referring to the weight capacity which is also another common question we get then I do no not have a…

view full answer...

Answer 5

The Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter part #RP85FR is compatible with the gooseneck tripod stabilizer Ultra-Fab Gooseneck Trailer Tripod Stabilizer part #UF19-950450 which I recommend. The Ultra-fab tripod has a height…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 12

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Fit of Electric Stabilizer Jack LC298707

Product Page this Question was Asked From

Continue Researching