Availability of Trailer Hub/Drum that Has Chevy 5 Bolt Wheel Pattern

Question

Question:

My trailer has the 4 bold flange and 15 chevy bolt pattern wheels. Will these fit my current wheels?

asked by: Andrew B

0

Expert Reply:

The Chevy 5 bolt pattern can mean a couple different patterns. The part # 84546UC3 is the very common trailer bolt pattern of 5 on 4-1/2 inch. The other common bolt pattern associated with Chevys is 5 on 5 inch like the part # AKHD-550-35-K which would be the other option.

If the distance between adjacent wheel studs on your hub is 3 inches you have a 5 on 5 inch. If you have 2-5/8 inches it's 5 on 4-1/2 inch.

expert reply by: Jameson C

0

click to enlarge

Answer 1

To install a 7-Way harness on your 1996 Dodge Ram without the factory connector, you will need two separate wiring harnesses because they don't make just one that'll do the job. The first harness you'll need is the Curt…

view full answer...

Answer 2

We have all of the wiring you need for your 1996 Ram, but there is no all-in-one harness available. First I recommend part #HM40975-11998. This is a 7-pole and 4-pole trailer connector with the bracket and wiring. This will hardwire to the existing…

view full answer...

Answer 3

On a 1996 Dodge Ram that came with a factory 4-Way trailer connector there is a factory harness you can plug into to install a brake controller. The harness is located underneath the dash, to the left of the steering column, taped to another…

view full answer...

Answer 4

You will need to remove an existing wheel and hub. Once this is done clean the bearings and seal off and record the part numbers, be sure not to mix up the numbers for the inner and outer bearings. With the bearing part numbers and seal part number…

view full answer...

Answer 5

For the correct hub/drum you'd want the part #AKHD-550-35-K which comes with the bearings you said you needed as well is pre-greased. If you were wanting an idler hub instead you'd want the part #AKIHUB-550-35-EZ-K.

view full answer...

Answer 6

The brake assembly and brake hub will not meet flush, but they will be close. I would double check that you have the correct parts and that all races and seals oriented correctly and fully seated. Then reassemble and tighten crown nut down until…

view full answer...

Answer 7

To be honest the brakes that were on your Lippert 5.2K axles were probably from Dexter Axle as they are the most common brakes on any trailer. Since your OEM brake controller on your Ram pickup worked with the old brakes it isn't likely that…

view full answer...

Answer 8

We do have a fantastic option for your enclosed trailer that has a 3,500 lb axle based on my research (though you will want to verify this); however, we do not offer torsion axles. The option we do carry is going to be a better one, the Timbren…

view full answer...

Answer 9

Technically, a trailer rated for 10,000 lbs can have 5 lug hubs. They are most common on 3,500 lb axles but can be used on the rare 4,000 lb axles as well. You could have a gooseneck or 5th wheel trailer with the 10,000 lb capacity and tandem axle…

view full answer...

Answer 10

The etrailer.com Hydraulic Trailer Brake Kit #AKUBRK-35-D referenced in your question do not, by themselves, lock up if the trailer were to come unhitched. This is the case with any hydraulic brake assembly. The mechanism that allows hydraulic…

view full answer...

Answer 11

Even though it is not a fit for it, it is not impossible to install the #C92UR Trailer Hitch Receiver on a 2019 Honda Civic Si. However, in order to do this, you will need to remove the center mounted exhaust pipe. I have attached a few photos for…

view full answer...

Availability of Trailer Hub/Drum that Has Chevy 5 Bolt Wheel Pattern

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching