Is Drilling Required to Install the TorkLift StableLoad Rear Suspension Upgrade # TLA7311

Question

Question:

Do the spring leaves have to be drilled to install this product ? I am approaching 80 yrs so dont look forward to drilling thru spring steel. ?? thanks

asked by: Terry M

0

Expert Reply:

The TorkLift StableLoad Rear Suspension Upgrade # TLA7311 that you referenced will require you to drill the leaf springs for installation. We do offer a few other solutions for your 2001 Dodge Ram that will allow you to install them without drilling into the leaf springs.

You could use the SuperSprings Custom Suspension Stabilizer and Sway Control Kit # SSA25 if your have a 2500 or 3500. If, however, you have a 1500 then you can use part # SSA5MTKT instead. These stabilizers will supplement your OEM springs and help stabilize your current suspension system for a better ride.

expert reply by: Jon G

0

Answer 1

Yes. I double checked this with TorkLift and the TorkLift StableLoad Rear Suspension Upgrade w Quick-Disconnects - Lower Overload Springs - Universal #TLA7311. These are a universal fit part, so they're designed to fit on a wide variety of…

view full answer...

Answer 2

The TorkLift StableLoad Rear Suspension Upgrade part #TLA7311 is a universal kit therefore comes with drill bits for applications that require a hole to be drilled into the leaf spring. The 2016 Ram 3500 already has the hole pre-drilled for you…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 8

I recommend going with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL89DQ for hauling around an in-bed camper with your 2024 Ford F-350 Super Duty. I really like this kit because it has the higher 7,500 lb rating (which you don't…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

The best air bag kit for your 2020 Ford F-250 Super Duty with a single rear wheel are the Firestone Ride-Rite Air Helper Springs because they are the strongest, most durable air bags on the market to provide you with optimal support for your…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...