Will the Ground Clearance of the Draw-Tite # 75992 on a 2011 Ford Edge be an Issue When Towing

Question

Question:

2011 ford edge Limited FWD. I believe every Ford Edge that I have seen with a trailer hitch had the facia cut out. Is that difference in height between the P/N 75992 and the others going to be an issue when I rent or buy a trailer?

asked by: Tim R

1

Helpful Expert Reply:

You should have no issues being able to tow a trailer behind your 2011 Ford Edge Limited after installing the Draw-Tite Max-Frame Trailer Hitch Receiver # 75992. You will simply need to find a ball mount that has the correct rise or drop to ensure that it is level. When we installed this trailer hitch on a similar 2011 Edge (see attached video) we found from the ground to the top of the inside of the hitch receiver was about 13-1/2 inches. You can use this measurement and the attached ball mount article to help you choose the appropriate ball mount from our selection that I have linked for you.

If you will be towing a few different trailer then what you may find helpful is using an adjustable ball mount like part # 63070 which can be adjustable for a 4-3/4" drop all the way to a 5-11/16" rise.

If you don't already have wiring for your trailer on your 2011 Edge then I also recommend installing the Tekonsha T-One # 118515 which will give you a 4-Way connector at the rear of your Ford Edge to activate the lights on your trailer. An installation video for this product has been linked for you to review as well.

expert reply by: Jon G

1

Answer 1

I recommend to switch the existing hitch to the Draw-Tite instead of using an adapter because adapters cannot be used with weight distribution and they cut the tongue weight rating of the hitch in half. The only Class III hitch available for the 2008…

view full answer...

Answer 2

The Draw-Tite trailer hitch, #75992, fits all models of the 2009 Ford Edge except the Sport model so it will fit your AWD model provided it is not a Sport. If it is a Sport, you would use #75686. In terms of what capacity you should use, you will…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

Yes, we have the Curt Trailer Hitch Receiver #C84BR which is confirmed to fit your 2024 Ford Maverick. This will provide you with a 2" receiver. We also have the Curt 4-Way #C59496 which will allow you to connect to most small utility trailers…

view full answer...

Answer 8

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 9

The Ventline Exterior Wall Vent for RV Range Hood, #V2018-01 does not have a screen. The vent is 11-1/2" by 5-1/2" with a 10 bolt pattern. Please note the linked product review video. the holes are set in from the edge by about 1/2" to…

view full answer...

Answer 10

I really like the etrailer Trailer Hitch Receiver #e66AR for your 2011 Mercury Grand Marquis for a few reasons; it has the matte black finish that blends in with any black trim on your vehicle and hides scratches from road debris, plus it has the…

view full answer...

Answer 11

Yes, only the receiver on Draw-Tite trailer hitch #75992 will be visible after installation on your 2013 Ford Edge. Take a look at the picture I have included that shows the hitch installed. I have also linked the instructions for you. If you plan on…

view full answer...

Answer 12

The Tow Ready Custom Fit Vehicle Wiring Harness, #118515, will install inline with your 2011 Ford Edge SEL tail light wiring connectors and power for the trailer lighting will be supplied by the vehicle battery, only requiring a few milliamps of draw…

view full answer...

Will the Ground Clearance of the Draw-Tite # 75992 on a 2011 Ford Edge be an Issue When Towing

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching