Replacement Clearance Lights for 2001 Dutchmen Travel Trailer

Question

Question:

Looking to replace faded clearance lights on rear sides of travel trailer... only issue is I cant tell what color they are because theyre faded! They are near brake lamps but on side of trailer 6inch from rear and about two feet off ground. 2001 Dutchmen

asked by: Loyd

0

Expert Reply:

It looks like you are needing replacement red clearance lights for the rear of your 2001 Dutchmen Travel Trailer. In order to choose replacement assemblies, I recommend taking a couple measurements on your existing units. Based on the picture you provided, something like the Optronics LED Trailer Clearance, Side Marker Light # MCL31RB might be an excellent replacement.

This red, LED clearance light measures 4 inches long, 2-1/16 inches wide and 1 inch deep. It features a 2-wire design and a 3 inch mounting dimension. I have attached a short video demonstration on this assembly that you can check out, along with a link that will take you to our available selection of red clearance lights for you to look through.

expert reply by: Chris R

0

click to enlarge

Answer 1

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 7

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 12

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...