Dimensions of CE Smith Double U-Bolt Bolster Bracket # CE10196G

Question

Question:

Can you please let me the deminsions of the bracket without the swivel attachment. Also the distance between the holes.....I need minimum 12inch clearance from holes. Will be attaching to 12 inch plank overlap. Attaching latter to lift and need to use bracket to sandwich connection.

asked by: George

0

Expert Reply:

The 15" bolster bracket you mentioned, # CE10196G, has 7 3/4" clearance from the edge holes to the end of the bracket. (See diagram.) The distance between the holes is 1 3/4" horizontally and 1/2" vertically. Since the holes are slotted, you should be able to get your 12" of clearance.

expert reply by: Amy W

0

click to enlarge

Answer 1

As the CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies #CE10196G-4 does come as a pack of 4, we do have them individually as well. The bolster needed is the #CE10196G and the swivel bracket is the #CE10206G. You will need 2 of each of…

view full answer...

Answer 2

The Stainless Steel Hex Lag Screw #FA74521 contains one 3/8" diameter, 1-1/4" long lag screw.

view full answer...

Answer 3

I went and pulled CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies #CE10192GA-4 from our warehouse to get the dimension you are looking for and found it to be 5 inches from the top of the bracket down to the nearest part of the u-bolt…

view full answer...

Answer 4

The CE Smith Brackets #CE10196G-4 you mentioned do not have a stated weight capacity but as long as you install them properly and use your best judgement with placement and with the bunks you'll be fine with what you are doing. Here's…

view full answer...

Answer 5

Your best option is going to be bolster bracket set #CE10196G-4 which is a quantity of 4 so if you wanted 6 you would need 2 sets and you would have a couple of spares should they be needed. These are 16-1/4 inches long with some adjustability due to…

view full answer...

Answer 6

For U-bolts for your 3" x 3" frame you will want something that is slightly larger. If the measurements were listed as exactly 3" it isn't going to fit. What you need is the CE Smith U-Bolts - Galvanized - 3-13/16" Long x…

view full answer...

Answer 7

Since you've got a boat trailer, you'll want to use something that offers a good level of corrosion resistance. We have two different u-bolts that would work for you, one that's zinc plated #CE15252A and one that's stainless steel,…

view full answer...

Answer 8

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…

view full answer...

Answer 9

If your Dutton Lainson roller bunks have a flat bottom surface like part #DL21741 then you can mount them directly to the CE Smith Bolster and Swivel Bracket Assemblies #CE10196G-4 as shown in the linked photo. These are the tallest ones we offer. If…

view full answer...

Answer 10

The CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies part #CE10196G-4 can be used on a 4" frame with the CE Smith U-Bolt part #CE15254A.

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Dimensions of CE Smith Double U-Bolt Bolster Bracket # CE10196G

Product Page this Question was Asked From

Continue Researching