Does Screw Come with Replacement Plastic Gear # BVD0121-00

Question

Question:

Does the screw to attach the BVD0121-00 come with the order or is there a seperate part number for the screw?

asked by: Dan

0

Expert Reply:

You'd need the screw part # VC0270-00 as it is not included with the # BVD0121-00.

expert reply by: Jameson C

0

Answer 1

Appreciate the photos and based on those we do have what you are needing, which is the gear motor and gear for your Ventline V2119 roof vent: - Replacement Gear Motor with Pinion Gear #BVB0601-00 - Replacement Plastic Gear #BVD0121-00

view full answer...

Answer 2

You are correct in your description of how to wire in a new auxiliary battery in your enclosed trailer. You will take the 7-Way's 12V power feed and route this to the positive terminal on the auxiliary battery, and you will ground the second…

view full answer...

Answer 3

I believe the part #BVD0121-00 is exactly what you would need. I went and measured one from our warehouse and it is 1-9/16 inches in diameter and 1/4 of an inch thick.

view full answer...

Answer 4

We carry two different replacement operator and knob assemblies for the Ventline trailer roof vents. The operator you referenced, #BV0115-04, will work with vent covers that have either a slot or a slotted bracket for the end of the operator arm to…

view full answer...

Answer 5

If the lift motor on your Ventline #V2119-601-00 runs when you try to operate it then it sounds like you need the Replacement Plastic Gear #BVD0121-00 which operates the lift arm. To replace the lift motor you need the Replacement Gear Motor with…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...