Can Roadmaster Sway Bar Fit 2004 Dodge Ram 2500 with Timbren Kit Installed

Question

Question:

Will Sway Bar for Dodge 2500 fit with timbren load levelers?

asked by: Courtney S

0

Expert Reply:

Yes, the Roadmaster sway bar part # RM-1129-124 will fit your 2008 Dodge Ram 2500 and will work with a Timbren system installed as well. The two would not interfere with each other at all.

expert reply by: Jameson C

0

Answer 1

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Answer 2

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 5

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Answer 6

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

There is a suspension enhancement option for your 2021 Entegra Vision XL built on a Ford F-53 chassis, but I verified with the manufacturer that the steering stabilizer only fits if you have at least a 24,000 lb GVWR. You're not out of luck…

view full answer...

Answer 10

There's a few differences. • The Curt #C31017 is manufactured in the US, while the Draw-Tite #65046 is manufactured in Mexico. • When installed, the Curt hitch will sit higher on the vehicle for more ground clearance. The underside of the…

view full answer...

Answer 11

Hellwig lists the Hellwig Rear Anti-Sway Bar #HE36MR as the correct fit for a 1998 Chevy K2500. As for fitment with the staggered shocks, you shouldn't have any issues and can even see this setup in the attached installation picture below. The…

view full answer...

Answer 12

I found the online version of the install instructions for the Exact Center stabilizers like the #RM47MR. What's fun is that just when you think you have found the correct step to address your problem it tells you to continue to the next step.…

view full answer...