Will Curt Front Mount Receiver # C31028 Fit a 1997 Jeep Wrangler with Double Tube Bumper

Question

Question:

Will it fit on my 1997 Jeep Wrangler with a tube style front bumper?

asked by: Brad B

0

Expert Reply:

If the double tube bumper on you 1997 Jeep Wrangler does not hang down any lower than the regular stock bumper would then Curt font mount hitch receiver # C31028 will fit. It has not been test fit on a model with the tube style bumper.

expert reply by: Michael H

0

click to enlarge

Answer 1

There is a 2 inch hitch that fits your 1998 Jeep TJ, but the #C13900 does not fit; instead, you can use the following: - etrailer Trailer Hitch Receiver #e43AR Then to add a 4-way, the correct fit is the T-One Vehicle Wiring Harness with 4-Pole…

view full answer...

Answer 2

Typically people will let the breakaway battery run the breakaway system and then would use the accessory battery to power the interior lights etc. This tends to work the best since your breakaway battery needs to always be charged and interior…

view full answer...

Answer 3

The Curt Front Mount Hitch, #C31028, does install under the bumper of your 1999 Jeep TJ and, according to my contact at Curt, will not interfere with the steering box or pitman arm. I have attached a photo showing what the hitch will look like once…

view full answer...

Answer 4

To add a front mount trailer hitch to your 2002 Jeep TJ with a tube style front bumper you will need to use Curt front mount hitch #C31028. It attaches to the frame of the Jeep and will sit underneath your front bumper.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Will Curt Front Mount Receiver # C31028 Fit a 1997 Jeep Wrangler with Double Tube Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching