Distance Between Hangers Using Tandem Axle Hanger Kit

Question

Question:

I just purchased 4 e54SR springs along with the APT5 hanger set . What is the recommended distance between the center of the equalizer bracket and the center of the spring hangers? Thanks

asked by: Gerald W

0

Expert Reply:

Since you have a tandem axle set up using double-eye springs # e54SR, the Tandem-Axle Trailer Hanger Kit for Double-Eye Springs # APT5 recommends a distance between the front and center hangers of 29-1/2" and a distance between the center and rear hangers of 29-1/2".

expert reply by: Kyle S

0

click to enlarge

Answer 1

Leaf spring hangers come in different heights to provide more or less clearance between the trailer body and the suspension. Manufacturers determine the best spacing for the axles and sizes of the hangers, leaf springs, equalizers, and shackle straps…

view full answer...

Answer 2

We can set you up with all of that. We do offer a 3,500 lb 95" hub face axle #e68GR. The spring seats on this axle are at 80", so we can sell you a few loose spring seats #TRSS238 and you can have them attached at 76". We can also…

view full answer...

Answer 3

The hanger spacing for the #APT4 with 25-1/8" leaf springs is 27-3/4" on center. I have attached a drawing for your reference.

view full answer...

Answer 4

The position of the axle should dictate the position of the springs and hangers not the other way around. With that being said, in order to determine proper placement of the hangers you will want to take the the distance between the two eye holes on…

view full answer...

Answer 5

You will want to space your hangers 30-3/4" on center from front to center and center to rear. Your setup is similar to our Tandem-Axle Trailer Hanger Kit #APT5. I have linked our article below for determining proper trailer axle position if you…

view full answer...

Answer 6

It is possible that hanger kit #APT5 will fit your trailer. But you will need to take the measurements first like you said. When taking the measurements you will want to have the weight off of the trailer by jacking up one side. Depending on the axle…

view full answer...

Answer 7

There are a few differences between slipper springs and double-eye leaf springs. Slipper springs normally have a higher weight capacity, and fewer moving parts, but they tend to ride a little rougher than double-eye. You will need to know the length…

view full answer...

Answer 8

There is a way to determine axle placement on a trailer. I have included a picture that explains the calculations needed to determine axle placement. It is based on tongue weight and gross trailer weight. If you know the combined axle capacity then…

view full answer...

Answer 9

Thanks for the measurements! You are correct that the Tandem-Axle Trailer Hanger Kit for Double Eye Springs - 3-1/4" Tall Front/Center/Rear #APT5 you were looking at is designed around 29-1/2" hanger spacing but your suspension is a bit…

view full answer...

Answer 10

We don't carry the MR4 leaf springs but based on my research they look like they are 26 inch double-eye springs like part #e94SR. For springs of this length and the Tandem-Axle Trailer Hanger Kit for Double-Eye Springs #APT4 the hangers are going…

view full answer...

Answer 11

Based on my research, when using the Universal Group Leaf Springs #SP-222275 that has a spring eye length of 24-7/8 inches with either the Redline Tandem Axle Hanger Kit #APT4 or #APT3HD, you will want a distance of 29-1/2 inches between the hangers…

view full answer...

Answer 12

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Distance Between Hangers Using Tandem Axle Hanger Kit

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching