Tips for Removing Nut on Jack Mounting Bracket P9012-00 when the Jack is In the Way

Question

Question:

What is the easiest way to remove the locking nut to remove the jack from the bracket ? Not much if any room to work with.

asked by: Anthony D

0

Expert Reply:

Since the jack tube is blocking the nut on mounting bracket # P9012-00 your best option is to use a box end wrench with an offset. So instead of a straight wrench it would have a bend in it. This will allow you to get a straighter angle with which to turn the nut. You can get offset wrenches anywhere tools are sold such as Sears, Home Depot, Lowe's and so on.

expert reply by: Michael H

0

Answer 1

Yes, the Fulton Bolt-Thru Swivel Marine Jack #F1411300301 has a matching 3" x 3" bolt pattern to match up to your welded on mounting bracket.

view full answer...

Answer 2

You would need to replace the weld-on jack with another weld-on jack of the same type. The bolt on jacks have a different mounting bracket than the weld-on ones. You could use #FXP15W and you may also need bracket #P9012-00 if the old one turns out…

view full answer...

Answer 3

I wish it would, but the Jack Mounting Bracket #P9012-00 you were looking at has pin holes that are all 3" apart on center where the Fulton XLT Bolt-Thru Swivel Trailer Jack #F141133 uses a mounting bracket that the lower holes are 3" apart…

view full answer...

Answer 4

I went out to the warehouse and took a bunch of measurements of the Jack Mounting Bracket #P9012-00. The side flanges don't stick out towards the trailer as far as the top flange. The distance from the far edge of the top flange to a side flange…

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Tips for Removing Nut on Jack Mounting Bracket P9012-00 when the Jack is In the Way

Product Page this Question was Asked From

Continue Researching