Electric Brake Controller Connector Location on a 2015 Nissan Pathfinder

Question

Question:

Read all reviews, still cant find plug under dash to plug 3050 into. can you be more specific of location. Thanks And yes I have tow package

asked by: Mark

0

Expert Reply:

The connector to install an electric brake controller, like the Primus IQ # TK90160 you purchased, that is under the dash of your 2015 Nissan Pathfinder is pretty hard to find. In addition to that it's also capped and covered in tape.

Take a look at the video I've linked. The install isn't on the same controller but it's on a 2013 Pathfinder that uses the same # 3050-P connector. Skip ahead to about the 2:55 mark and our installer starts showing the location under the dash.

expert reply by: Charles S

0

Answer 1

The connector that attaches to the wiring adapter, part #3050-P on your 2015 Nissan Pathfinder should be located under the dash near the brake pedal. There should be a 6-pin connector that mates with the 3050-P. Since you mentioned you have the…

view full answer...

Answer 2

If your tow package includes a built-in port beneath your vehicle dash, I recommend installing the brake controller via this Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers for Nissan vehicles, Item #3050-P. This adapter is confirmed…

view full answer...

Answer 3

The relay of the running light circuit on your Pathfinder is in the relay harness behind the passenger floor board kick panel. If you check out the install video I attached the first thing shown is how to access this area.The correct fitting relay is…

view full answer...

Answer 4

Trailer running lights not working with certain Nissan vehicles is a common problem with an easy fix. There is a relay for the trailer running light circuit that is located in the fuse box (in the cab). If that relay is missing or no longer functions…

view full answer...

Answer 5

The towing relays in a 2015 Nissan Pathfinder are located in the rear cargo area on the driver's side. Please refer to the linked video at the 4:00 mark and to the photo that shows this placement. I also linked all of our trailer wiring products…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...