Replacement Jack Recommendation for Replacing Shelby 6108SW

Question

Question:

Need a replacement jack for Shelby Mfg# 6108SW 8,000 lbs capacity

asked by: Richard V

0

Expert Reply:

The closest jacks to the 8K Shelby 6108SW that we offer at this time are our Square Direct Weld Jack with Footplate, part # TJD-7000, and the 7.2K-rated Bulldog Square Jack # BD180354. For an 8K square side-wind jack we have Pro Series # PS1400860383.

expert reply by: Adam R

0

Answer 1

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 2

The return springs in landing gear jacks are not replaceable or repairable unfortunately so if you have the #TJD-12000SP-R2NH.

view full answer...

Answer 3

It sounds like you're talking about the rod and nut on the #TJD-12000SP-R2NH. We have the following replacement parts available: -Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks #TJD-12000-RODNUT -Replacement Sidewind Gear…

view full answer...

Answer 4

Weight distribution systems do typically create some noise whether it is creaking, scraping, or even clunking. This is normal and is a result from the metal on metal contact. If you are using the Pro Series system #49570 or a similar system with a…

view full answer...

Answer 5

If you look at the backs of the brake assemblies there should be a hole where the magnet wires come out and a little opaque plastic strap. So if you are looking at the back of the assembly and those items are on the left then it is the left side…

view full answer...

Answer 6

From previous customers who have tried it we know that the Fulton jack #FTJ120W0301 fits the exact same mount as the Shelby jack so this would be your best option.

view full answer...

Answer 7

It is possible the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit the same mount used by your Shelby 5776 jack but we do not have the exact dimensions of the mount used by your Shelby jack so you will need to take a quick…

view full answer...

Answer 8

Connection three 10-gauge wires together is going to be best accomplished by soldering the connections as this is the most secure method. We have a solder gun that comes with solder as well with part #PTW2012. I realize that not everyone knows how to…

view full answer...

Answer 9

The torque specs for 9/16" diameter u-bolts like the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles part #APUBR-9 will be a range, from 65 ft. lbs. to 95 ft. lbs. If the tie-plates start to bend inside this range that would be…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Replacement Jack Recommendation for Replacing Shelby 6108SW

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching