Replacement Fantastic Vent Fan Motor For Auto Lift Unit Without Thermostat or Remote

Question

Question:

Need new fan motor. Label on existing motor reads XW8100DMWD6WH. Do you carry it? Auto lift, no thermostat or remote.

asked by: Keith V

1

Helpful Expert Reply:

The Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans # FVK8017-00 is what you need to replace your current motor.

expert reply by: Jason S

1

click to enlarge

Answer 1

The Chevy Spark can be flat towed only if it has a manual transmission. To flat tow the Spark, you will need a base plate, I recommend Blue Ox Base Plate Kit, #BX1725. For the tow bar, I recommend The Blue Ox Avail Tow Bar, #BX7420. This non-binding…

view full answer...

Answer 2

It sounds like you might have a Create-A-Breeze B8100 model fan, which is a Fantastic Vent series fan. The correct replacement for the fan and motor on 8000 series units is the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans…

view full answer...

Answer 3

I reached out to a representative of Fan-Tastic Vents who confirmed that the correct replacement for your Fan-tastic model 8100DM is the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans #FVK8017-00. This comes with a bow-tie…

view full answer...

Answer 4

Fan-Tastic Replacement Fan Motor Assembly Kit #FVK8017-00 is indeed the correct part for your Create-a-Breeze model 8000 vent. I confirmed with my contact at Fan-Tastic vent.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 9

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 10

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 11

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 12

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Replacement Fantastic Vent Fan Motor For Auto Lift Unit Without Thermostat or Remote

Product Page this Question was Asked From

Continue Researching