Wire Colors for Installing Brake Controller in 2017 Chevy Colorado

Question

Question:

I purchased a Curt 51110 brake control for my 2017 Colorado. The wires from the controller are Black, White, Red and Blue. The truck wires are black, white with blue stripe, red with blue stripe and red. which wires connect to each other ? I connected black to black, white to white with blue stripe red to red with blue stripe and blue to blue and the controller does not work. please advise.... thank you

asked by: Roger R

1

Helpful Expert Reply:

I attached a picture that has a chart which shows how to wire up a brake controller to your 2017 Chevy Colorado.

If you check out the install video you can see how this would install on a similar 2015 Colorado as yours.

expert reply by: Jameson C

1

click to enlarge

Answer 1

We've actually got a great installation video of a Tekonsha P3 #90195 that I've linked to this answer that you can use to follow along with the installation process, but I'll also match up the wires for you below based off of…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 7

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 8

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like…

view full answer...

Answer 9

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 10

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 11

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 12

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...