Type of Vehicle Connector Required to Install Hopkins Smart Hitch Backup Camera HM50002

Question

Question:

Will the wiring harness for this camera plug into the 7 pin trailer wiring on an 06 jeep commander?

asked by: Werner

0

Expert Reply:

The Hopkins Smart Hitch Backup Camera and Hitch Aligner System # HM50002 plugs in to any vehicle that has a round U.S. Car type connector plugged in the rear side of its 7-way. An example of such a part is the Hopkins Endurance Quick-Install 7-Way Trailer Connector # HM42190.

At the rear of this vehicle socket is a round U.S. Car connector that can be removed, and then plugged back together with the camera's own mating connector inserted in between. Please refer to the linked photo that shows the round connector.

expert reply by: Adam R

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 8

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 11

No, they do not but I have a set that does. They are the Reese Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches item #RP30035. These are confirmed to fit the 2002 Ram 2500 with the 6-1/2' and 8' bed lengths. I have…

view full answer...

Answer 12

After installing The Furrion Heat Strip Add-On for Furrion Air Conditioner #FR27PR on your Jayco Jay Feather 27BHB the heating strip is utilized using the existing thermostat. This heating strip will work best in smaller spaces where the temperature…

view full answer...