Slightly Larger Version of the Atwood Drill Adapter # AT85385

Question

Question:

I have a very old 1974 Swiss Colony fifth wheel camper that I purchased this part for and it looks like my existing crank is about the size of a 3/4inch conduit. The new one will not fit onto the shaft. Do you have a larger one ?

asked by: Mike G

1

Helpful Expert Reply:

We do have the # UF48-979071 which is slightly larger than the Atwood part # AT85385. The Atwood has an opening of .53 inches whereas the Ultra Fab is .66 inch.

See attached picture.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Thanks for the photos and like you said, they are the Atwood jacks 86065, which are discontinued jacks. What that means is the best option we can offer are new, manual camper jacks, the Brophy Cable Camper Jacks. Based on my research, your 2014…

view full answer...

Answer 2

The Atwood manual crank you referenced we no longer carry. The Replacement Crank Handle for Stromberg Carlson Landing Gear #LG-119226 is the manual crank we have that will work for your Atwood Electric Jack. This is a much longer option which would…

view full answer...

Answer 3

If the scissor jacks are easily raised/lowered with the manual crank but the drill adapter doesn't seem to be strong enough I'd say the first thing to try is charging the drill if it's a battery operated drill. If that does…

view full answer...

Answer 4

I see what you mean about the cover being "recessed" into the front of the trailer. After looking thru a few pictures of these 2005 Trail Lite Hybrid trailers, it appears to be a fairly unique tank cover. I am sorry to say that we do not…

view full answer...

Answer 5

Thank you for providing that picture. In order to install the #SSR54FR on your Dometic AC you will start by removing the white wire coming from the compressor to the run capacitor and connect it to the blue wire on the SoftStartRV. Next, take the…

view full answer...

Answer 6

The Ultra-Fab T-Slot Power Drill Adapter for Scissor Jacks #UF48-979071 will have a slot that is 1/4 inch wide and although not intended for your topwind trailer jack could maybe work. I've attached a picture that has several dimensions for you…

view full answer...

Answer 7

Our customers have told us that the #LG-119226 Replacement Crank Handle works with most Atwood landing gear. I've linked to a product description video featuring the replacement handle. I've also provided a close-up photo showing what the end…

view full answer...

Answer 8

The foam ring on the Ventline Vanair Trailer Roof Vent part #VP-543SP is a weather seal that is used to help seal the dome on the fan assembly. If you continue to use the fan without the foam ring you would be subjected to leaks which could then…

view full answer...

Answer 9

The height of the outer tubes on the Landing Gear Set - 36-1/2" Lift - 8,000 lbs #RVLG-8000 is roughly 29" without the legs and 32-3/4" with the drop legs included. The distance between the outer edges of the top and bottom weld stops…

view full answer...

Answer 10

If you have a Dexter 4 lug hub currently that would mean your trailer has a BTR sized spindle so to replace it with a 5 lug hub would require the part #8-258-5UC1 and you'd be set. This will fit your spindle in place of the 4 lug hub you have now…

view full answer...

Answer 11

Since you have a 4 on 4 inch bolt pattern currently that would indicate that you have a 2,000 lb axle so you could swap your current hubs pretty easily with the bolt pattern you are looking for with the part #34822545BX that you referenced. This hub…

view full answer...

Slightly Larger Version of the Atwood Drill Adapter # AT85385

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching