Troubleshooting Kuat Transfer Bike Rack that Moves in the Hitch
Question:
I have a Kuat Transfer bike rack that fits into a 1.25inch hitch. It has a fair amount of hitch wobble and their threaded hitch pin doesnt seem to totally deal with it. Do you have something that would work? Ideally I could lock it too.
asked by: Paul N
Expert Reply:
If you check out the test course video I attached for the Kuat Transfer TS02G that shows how stable it is on the road you'll see that the rack is supposed to be pretty stable once the hitch pin is tightened.
What is most likely going on is that the hitch pin may not be tight enough to remove all of the movement.
The easiest way to fix this is to tighten the hitch pin while you move the rack around in the hitch. This is the easiest way to get all of the movement out of the rack.
For a lock for both the bike rack and the bikes to the rack the part # PTSCLK12 would be what you need.
Product Page this Question was Asked From
Cable Locks and Hitch Lock for Kuat Transfer 2 Bike Rack
- Bike Locks
- Cable Locks
- Keyed Unique
- Steel
- Black
- Kuat
more information >
Continue Researching
- Video: Curt Trailer Hitch Installation - 2019 Audi A5
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Anti-Rattle Hitch Lock for Kuat Transfer Bike Racks - 1-1/4" and 2" Hitches
- Q&A: Kuat Rack Installation When Metal Ball Doesn't Fit
- Q&A: Why Can the Kuat Transfer V2 Carry a Heavier Bike Than the V1
- Q&A: How to Tell Difference Between V2 and V1 Kuat Transfer Bike Racks
- Shop: Replacement Rim Protector for Thule Circuit Roof Bike Rack
- Shop: Replacement Wheel Strap Assembly for Hollywood Racks Destination Bike Carrier
- Shop: Yakima EXO Swing Away Storage System w/ Enclosed Cargo Carrier and Cargo Carrier - 2" Hitches
- Shop: Replacement Cradle and Strap for Yakima FullTilt and FullSwing Bike Racks
- Video: Yakima EXO System Cargo Carrier and Enclosed Cargo Carrier Review - 2021 Subaru Outback Wagon
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: hitch
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Article: My Trailer Hitch Doesn't Fit
- Shop: Roof Rack
- Video: Draw-Tite Max-Frame Trailer Hitch Installation - 2024 Subaru Outback Wagon
- Search Results: cargo carrier
- Shop: Brake Controller
- Video: etrailer Class III Trailer Hitch Installation - 2024 Subaru Crosstrek
- Article: How to Measure for Trailer Hitch Drop
Susan
3/20/2024
I just installed a Kuat Transfer Rack to a 11/4 inch hitch. It wobbled quite a bit. I had tightened the hitch pin bolt as much as I could, There is an additional step which is not in the instructions. There is a tiny hex pin screw at the front of the hitch that you can tighten with the largest hex wrench included with the other tools which will tighten the ball bearing that is on the rack hitch part to make a snug fit. This stopped the wobble completely. https://www.youtube.com/watch?v=HG0pC2C2hm4 Look at 2:24 - 3:00