Can The Shank From One Weight Distribution System be Used on Another System

Question

Question:

I currently have a 10k Equalizer hitch about 10 years old. My new travel trailer is not supposed to use any WD bars over 750 lbs. I would like to stay with Equalizer. Can I use my current shank, and would everything else be included in your kit #EQ37061ET

asked by: Michelle D

0

Expert Reply:

Yes, you will be able to use your current weight distribution shank on the Equal-I-Zer Weight Distribution System, # EQ37061ET.

All the other needed parts will be included with the new weight distribution system. For installing the trailer ball to the weight distribution head, I recommend using a thin walled socket like # EQ70-00-4800. This socket is designed to work with Equal-I-Zer hitches

expert reply by: Jared P

0

Answer 1

By the phrase 'too tall for my trailer' I'm assuming you mean that the weight distributing shank won't place the trailer ball low enough for the trailer to be towed level (if not, please email me back and clarify). There are weight…

view full answer...

Answer 2

Yes, you can use a 2-5/16-inch hitch ball #EQ91-00-6100 with the Equal-i-zer Weight Distribution System #EQ37060ET that is rated for 6000-lbs. This system does not come with the ball so you can use the one above or a 2-inch ball #EQ91-00-6080. Either…

view full answer...

Answer 3

To install the hitch ball that comes with the Equal-i-zer weight distribution system part #EQ37061ET requires a thin-walled socket like the part #ALL643216. The ball is not assembled as it's easier to ship and package with everything…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 9

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Answer 10

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...