Brake Controller Wiring Instructions for a 2011 Chevrolet Silverado Z82

Question

Question:

Is z82 also correct for 2011 silv chevy

asked by: Charles C

0

Expert Reply:

The Z82 is a trailer towing package installed by GM the manufacturer of the 2011 Chevrolet, Silverado.

If you are installing a brake controller on the 2011 Chevrolet, Silverado, and it does not have a factory integrated brake controller, you will only need a brake controller like the Tekonsha Prodigy, item # 90885, that you mentioned. We have a video, see link, that details this installation and shows where to find the wires that are needed to splice to the wires on the brake controller.

If your truck has that factory integrated brake controller, and you wish to install an aftermarket model for towing a trailer with electric over hydraulic brakes, we have an informational article, see link, that details the installation in this situation.

Finally, if your truck is not equipped with the towing package you will need the Twist-in, 7-Pole, RV-Style Trailer Connector, item # PK11916, at the rear of the vehicle. You will also need to make some wire connections under the hood, see photo at right. We also have an article showing where these wires are located and how to connect them. You will also need two nuts for under hood wire attachment. The M6-1.0 Flange Nut, item # 185916, and the M8-1.25 Flange Nut, item # 185917, are the correct fasteners.

expert reply by: Robert G

0

click to enlarge

Answer 1

Assuming that the 7-way on the bumper is from the factory and the tow package harness can be unplugged from the rear of the connector, using a T-connector like #41157 is what I'd recommend. Simply temporarily unplug the connection at the rear of…

view full answer...

Answer 2

A tow package for a vehicle is usually a frame mounted trailer hitch and trailer wiring on a vehicle like your 2002 Dodge Dakota. If you have those two things you could pretty easily assume you have the tow package. Or, you can take the VIN of your…

view full answer...

Answer 3

Thank you for being very detailed with your question! The first step I would take is to make sure everything on the truck and trailer is wired properly. Your Prodigy brake controller should have the wiring adapter #3025-P which is custom for your…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 10

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Brake Controller Wiring Instructions for a 2011 Chevrolet Silverado Z82

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching