Can Suspension of Jayco 23B Kiwi Be Lifted

Question

Question:

Is there a lift kit I can install on my 23B? I have seen some people talk about a 2inch lift kit to give you more clearance and the ability to run bigger tires.

asked by: Clint B

0

Expert Reply:

We do have a great option for lifting a trailer like yours by moving the axles below the leaf springs if it is equipped with leaf springs.

Another option you have would be to lift the trailer. You can do this by moving the axles from being above the leaf springs to below the leaf springs.

The diameter of your trailer axle will determine the size of the parts that you will need to order. If your axle is 3 inches diameter, the Dexter Trailer Springs Over-Under Conversion Kit, # K71-385-00, would be a great choice and if your axle is 2-3/8 inch diameter you could use the Over-Under Kit, # K71-384-00. These kits can be installed without welding but the manufacturer strongly recommends having the new spring seat tacked in place on the other side of the trailer axle.

expert reply by: Jameson C

0

Kathy G.

1/11/2021

My Jayco 23b does not have leaf springs so which lift kit can I use for it? Th3e axel is bolted to the chasey.

Reply

Jon G.

1/14/2021

You probably have a Dexter Axle Torflex axle system that uses torsion arms instead of leaf springs. I'm attaching a link to our selection of lift kits for this style of axle but you'll want to confirm on the axle sticker or trailer info that's what you have. Our lift kits are specific to the Torflex axle number as well so you'll want to note what you have and make sure that it matches.

Helpful Links

s.aspx?qry=torflex+lift+kit

Reply

Answer 1

The Torflex Axles on your 2006 Jayco Jayfeather 23B will allow you to add a lift kit and utilize bigger tires. I didn't get your photos, but the measurements you gave will clearly allow this. There is no horizontal movement. You most likely have…

view full answer...

Answer 2

I would recommend you get Loadstar ST185/80D13 Bias Trailer Tires #AM1ST79. These tires have a capacity of 1,725 lbs at 65 psi and are the same size that you have on your trailer. With trailer tires you will always want to have them inflated to the…

view full answer...

Answer 3

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 4

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 5

Hello Dan, I can definitely help with this. It is completely normal for the Curt TriFlex brake Controller #C24VV to show the current gain setting when the brakes are applied, or when the manual override is pressed. It sounds like you have the gain…

view full answer...

Answer 6

The length Dexter posts for their leaf springs is the flattened length, so with the 072-042 having a length of 26" you would want to compare that to our 25-1/4" long springs as we measure their length with the spring relaxed. The 3-Leaf…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...