What Grease Seal Is Used in the Hub # AKIHUB-440-2-1K

Question

Question:

Hello, Do you guys offer the grease seal only from your part number AKIHUB-440-2-1K? Thanks inadvance.

asked by: Steven A

0

Expert Reply:

Yes, the grease seal you want is the part # 34823 which is what comes with the part # AKIHUB-440-2-1K you referenced.

expert reply by: Jameson C

0

Answer 1

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your…

view full answer...

Answer 2

I looked up the information on your TDE 46205 Hubs and found a couple of great replacements for you. The one you pick will depend on the number of wheel studs you have. For 5 wheel studs use the etrailer Trailer Idler Hub Assembly for 2,000-lb E-Z…

view full answer...

Answer 3

BTR and BT8 are the reference numbers for a standard trailer spindle size. When picking out a hub for a trailer you have to make sure that the hub is designed to fit the spindle. What you will need to do is measure spindles on your trailer where the…

view full answer...

Answer 4

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your 1992 Kristi boat trailer. The easiest way to determine the correct replacement bearings for your trailer is to remove the hub and find the part numbers…

view full answer...

Answer 6

I have personally not heard of anyone having the same issues you are with the Curt Q20 5th Wheel Trailer Hitch after such a short amount of time. I even searched though some of our reviews and also was not able to find any other instances of said…

view full answer...

Answer 7

Yes, this sliding bushing on the Curt Q20 #C16530 that you're referring to is a removable bushing (which is why it slides) and is completely normal. I've attached the section in the instructions where it refers to this bushing. Figure 10…

view full answer...

Answer 8

Since the jaws of your Q20 can't be adjusted or replaced your best solution is going to be a new hitch like with the Curt A20 part #C16140 which is the newer version of what you have now which has a much tighter jaw design that will be quieter…

view full answer...

Answer 9

You're needing a replacement O-ring for the bearing shaft. The bad news is that Curt doesn't offer that as a replacement part. The good news is that it's a pretty standard 31.5mm O-ring that you should be able to find at a hardware or…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

What Grease Seal Is Used in the Hub # AKIHUB-440-2-1K

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching