What are the Dimensions of the Replacement Drop Leg with Foot on # TJD-7000-FT

Question

Question:

Will the TJD-7000-FT jack leg foot work on a PRO SERIES brand 8,000# jack? Do you happen to have the exact outer measurements of the square portion of the leg?

asked by: Luke R

1

Helpful Expert Reply:

The square tube of the Replacement Drop Leg # TJD-7000-FT, measures 2 inches x 2 inches.

The overall length of this part is 18-1/4 inches tall and the foot plate measures 6 inches by 8 inches. The pin holes are 5/8 of an inch and the holes measure 4 inches apart.

If your current jack leg dimension are the same then this replacement leg will work.

expert reply by: Jared P

1

Answer 1

The wall thickness of the Replacement Drop Leg with Foot for etrailer and Ram Square, Direct Weld Jacks #TJD-7000-FT is approximately 1/8 inch.

view full answer...

Answer 2

For your drop leg, I recommend the Bulldog Square, 18-1/8" Tall Drop-Leg Tube - 7,200 lbs to 10,000 lbs #BD70129201 which has a tubing width of 2-1/4 inches. The replacement cap for the Fulton jacks is #F0917504-00. If you need the pin for the…

view full answer...

Answer 3

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

What are the Dimensions of the Replacement Drop Leg with Foot on # TJD-7000-FT

Product Page this Question was Asked From

Continue Researching