Grease Cap Recommendation to Fit Hub of Harbor Freight Utility Trailer with Bore 2.050 inch

Question

Question:

Harbor freight utility trailer, model 94564, grease cap measures 2.050, need a replacement but cant find this size

asked by: Doug W

1

Helpful Expert Reply:

The best option we have is the Bearing Buddy part # BB2047 which is a fit as it is designed to fit hub bores of 2.047 which is very close to what you have.

expert reply by: Jameson C

1

Answer 1

The hub bore diameter of 2.037" - 2.042" is a rather uncommon size but Harbor Freight Trailers generally do use some rather oddball parts in which replacements are hard to find. Although we do not have any standard grease caps that will…

view full answer...

Answer 2

The downside to buying a "bargain" trailer kit is that customer support, both in terms of helpful information and available replacement parts, can be scarce. The other issue is that products made to sell at a tempting price point may not…

view full answer...

Answer 3

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 4

I recommend the Dexter Trailer Idler Hub Assembly for 2,000-lb Axles, #8-258BTUC1 with a 5 on 4-1/2 bolt pattern and wheel size of 13" to 15".

view full answer...

Answer 5

There unfortunately isn't a guide to tell us the size needed for your specific trailer, but it's really easy to measure for the correct size lug nuts. You'll want to use a set of calipers #PTW80157 to measure the diameter of the wheel…

view full answer...

Answer 6

Since most trailer manufacturers do not make wheel and tire information available to the general public, it is hard for me to tell you what size lug nuts you have on the wheel. I can tell you they do have caps over them. The most common size of lug…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Grease Cap Recommendation to Fit Hub of Harbor Freight Utility Trailer with Bore 2.050 inch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching