Brake Controller Install Connector Recommendation for 2010 Ford E-350 Van

Question

Question:

I have a 2010 Ford E350 Super Duty. What color is the wire that I hook the red wire from my brake controller to the stop light switch?

asked by: Raymond E

0

Expert Reply:

Actually all you need to install a brake controller in your 2010 Ford E-350 Van is the correct install harness part # 3034-P. Basically this plugs into the back of your brake controller and then plugs into the port under the dash of the van.

If you watch the install video attached you can see a van just like yours having a brake controller installed.

expert reply by: Jameson C

0

Answer 1

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 2

Trailer wiring color codes can vary greatly so I have a solution for you, but I can't tell you which color wire goes where on your trailer for wiring up a new 7-way. However, you may look around the wiring junction box or pin box of your…

view full answer...

Answer 3

I have exactly what you need to install a 7-way trailer wiring harness on a 2001 Ford E-350. That said, they don't make a direct plug and play 7-way for this vehicle so you will need to start with a 4-way first like the T-One Vehicle Wiring…

view full answer...

Answer 4

Some 2012 Ford E series vans will have a factory plug and some will not. If your van came with a factory trailer connector then the wiring is already there and active. But if it did not come from the factory with a trailer connector, the factory…

view full answer...

Answer 5

I would be happy to help you set up your 2010 Ford E-250 for towing. I can confirm that the Curt Trailer Hitch item #14055 you were looking at will fit your E-250. I have listed the parts below you will need along with installation videos and a…

view full answer...

Answer 6

I have a solution for you that I can provide, but we aren't going to have a custom fit hitch to fit a vehicle like what you referenced. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...