Is Brake Line Fitting On Demco Designed For 3/16-inch Brake Line

Question

Question:

Is the input threaded for a standard flared 3/16 brake line fitting?

asked by: Les S

1

Helpful Expert Reply:

The fitting on the Demco Replacement Hydraulic Cylinder Assembly # DMSB9776M is designed for a flared 3/16-inch brake line. I confirmed this with my contact at Demco.

expert reply by: Jeffrey L

1

Answer 1

Nearly all 2,000 lb axles have a spindle that is 1 inch in diameter where both bearings ride. If that's what you have then the bearing kit part #BK1-100 would be what you need as it fits that spindle.

view full answer...

Answer 2

Yes, a standard 3/16 brake line fitting threads into the etrailer.com Replacement Wheel Cylinder, #AKBRKR-H7-R. If your trailer currently has hydraulic trailer brakes on axles ranging from 3,500 lbs to 7,000 lbs, then your existing brake line fitting…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Is Brake Line Fitting On Demco Designed For 3/16-inch Brake Line

Product Page this Question was Asked From

Continue Researching