Picking Out Bearing Kit for Trailer with 2,000 lb Axles

Question

Question:

I need to replace the bearings model is st6208ua five lug 13inch rim 2000lbs axle

asked by: Michael E

1

Helpful Expert Reply:

Nearly all 2,000 lb axles have a spindle that is 1 inch in diameter where both bearings ride. If that's what you have then the bearing kit part # BK1-100 would be what you need as it fits that spindle.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Yes, you can remove your weld-on coupler and install a new bolt-on coupler that fits a 2 inch ball. There is just a few things you need to do to before and when installing. You need to know what channel size and the weight capacity you will need…

view full answer...

Answer 2

Yes, you can absolutely drill holes in your trailer tongue to install the 10,000 lb capacity Buyers Products Straight Tongue Trailer Coupler #3370091560. This is a pretty common occurrence due to the various bolt hole patterns of straight tongue…

view full answer...

Answer 3

You can replace a 4.80-8 trailer tire with a 4.80-12 or a 5.30-12 trailer tire, but there are a few things to consider before making the change. First, 4.80-12 and 5.30-12 tires are going to have a larger overall diameter than a 4.80-8 tire, by about…

view full answer...

Answer 4

Yes, a 5.30 x 12 tire will fit the same rim as a 4.80 x 12 tire. Both tire sizes fit on a 4 inch wide rim. There are a couple of things to consider when changing tire sizes. First, the larger 5.30 will be approximately 1.4 inches taller than the 4.80…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It does look like you are missing a wire connection on your solenoid. I attached a picture that shows a wire lead ran to the same terminal you just have rans with that copper bar. I believe that's the missing connection you need to make.

view full answer...

Answer 7

I have attached the installation instructions for the Hopkins Engager Trailer BreakAway Kit, part #20099. This kit includes a charger and an LED tester and will work with single and tandem axle trailers. I have also attached a link to an installation…

view full answer...

Answer 8

The Hopkins Engager Trailer Breakaway Kit, part #20099, uses the 12V power wire on your vehicle 7-way connector to charge the breakaway battery so it can activate your trailer electric brakes in the event of a trailer disconnect. Your tow vehicle…

view full answer...

Answer 9

No, it does not matter which wire you use for the ground and which is used for power when wiring electric brakes. Each can be used for either purpose.

view full answer...

Answer 10

We do offer the Replacement Trailer Hub Bearing, part #15123 for your trailer but I was unable to find a cross-reference for the Timken 09067 bearing you stated you need. You can measure the inner diameter and see if there are any bearings from the…

view full answer...

Answer 11

Those are Warner trailer brakes. This style is not made anymore and replacement parts are hard to find. We have some parts for the larger Warner assemblies but NOT the 12 x 2 inch ones. Most people end up replacing them. You will have to have…

view full answer...

Answer 12

The Replacement Inner Trailer Hub Bearing for 15123 is item #15123. It has a inner diameterof 1.250. The matching race is #15245. Since your other bearing measures 1.750" it is a match with, Replacement Trailer Hub Bearing - 25580 Item #25580.…

view full answer...

Picking Out Bearing Kit for Trailer with 2,000 lb Axles

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching