Inno Roof Rack Recommendation for a 2011 GMC Acadia with Factory Side Rails

Question

Question:

Will this fit a 2011 Acadia with raised roof rails? I didnt see it listed but your videos seem to Indicate it will. Thanks

asked by: Darren

0

Expert Reply:

That is a good looking vehicle! I checked with Inno and I am happy to report that foot pack # INFR will fit the raised side rails on your 2011 GMC Acadia. There is also a silver set if you prefer, # INFR-6. For the crossbars that will fit the feet and your Acadia use # INB117.

expert reply by: Michael H

0

click to enlarge

Answer 1

For the lowest cost roof rack option that will fit both your 2005 Pontiac Montana and 2010 Subaru Forester, both with side rails, I recommend using Inno feet #INFR with 50 inch bars #INB127. This system will be fast and easy to install or remove and…

view full answer...

Answer 2

The Malone Universal Crossbar System #MPG201 is a more economical choice but it still does a good job. The design and quality of Thule's system is why they have such a large difference in price. Whether you go with the Thule Crossroads system…

view full answer...

Answer 3

To transport all 3 of your kayaks with your 2018 VW Golf SportWagen you will need to go with a set of roof rack crossbars and a post/stacking style carrier that mounts to them. Starting with the roof rack I recommend an Inno Square Bar System that…

view full answer...

Answer 4

For a square bar roof rack for your 2010 HHR with raised roof side rails we do have options from Thule and Inno which use either 42-inch or 43-inch bars. These can be seen on the linked page along with all other rack brands and rack types. For a cost…

view full answer...

Answer 5

I have some great roof rack options for a 2020 Subaru Forester. The best size will really come down to what you are looking to carry. I have attached a nice chart below that gives some better insight on this. As you can see, in order to carry both a…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 10

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...