Replacement Trailer Brakes and Hubs for 2007 Jayco Jayfeather 25z

Question

Question:

Im replacing factory hubs,brakesandbearings.Im not sure if hub assembly #AKHD-545-35-EZ-K is what i need. The only #s i can find is on the brakes 023-026-00lh and023-027-00rh. Brakes are 10x 2 1/4inch /4 bolt flange/ 5 on 4 1/2inch lugs. According to this info, will this hub and bearings work on my dexter axle. Im considering brake kit dexter 23-26-27. 2007 Jayco Jayfeather 25z Thanks

asked by: Rick

0

Expert Reply:

The brake assemblies you have are the same as part # 23-26-27 which is a standard 3,500 lb axle setup. This means that we know the correct brake hubs you'd need are # AKHD-545-35-EZ-K that you referenced. This comes with new bearings and seals as well.

expert reply by: Jameson C

0

Answer 1

To add a lift kit to your 2012 Jayco trailer you should need the Torflex Lift Kit #K71-723-01 designed for a #9 Torflex axle - I don't have the specifics of what came on your trailer even with the provided VIN so you'll have to check on your…

view full answer...

Answer 2

While it may be possible that a 3,500 lb. brake assembly will fit your 3,000 lb. axle, it is recommended that you stay with the 3,000 lb. size intended for your axle and use the part number #K23-472-473-00 for a replacement. If you are dead set on…

view full answer...

Answer 3

The Dexter Electric Trailer Brake Kit part #23-47-48 does not come with hubs/drums. If you would like to add these as well you'd need the Easy Grease Trailer Hub and Drum Assembly for 2K Axles part #AKHD-545-2-EZ-2K for L44649 (1.063") or…

view full answer...

Answer 4

The 3k torsion axles like what you have on your 2002 Jayco Qwest trailer use the same hub/drums as 3,500 lb axle so for a replacement you'd want the #AKHD-545-35-EZ-K. Then for a set of self-adjusting brake assemblies you'd want the part…

view full answer...

Answer 5

The 2,000 lb, 7" Electric Trailer Brake Kit #AKEBRK-2 and Dexter Electric Trailer Brake Kit #23-47-48 so use the same retainer clips for the magnets. These retainer clips are not available by themselves but what you can do is replace the magnets…

view full answer...

Answer 6

The Trailer Hub and Drum Assembly part #AKHD-545-35-K for standard or part #AKHD-545-35-EZ-K for easy lube are what you need to replace the hub on a 1994 Haulmark Elite 24' Trailer.

view full answer...

Answer 7

Appreciate all that info and you are on the money with what you need for your 2014 Jayco Jay Flight Swift SLX with its 3,500 lb axle and 5 on 4-1/2" bolt pattern: - Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles #AKHD-545-35-EZ-K This…

view full answer...

Answer 8

The brakes you have now and 10" x 2-1/4" brake assemblies like the #AKEBRK-35-SA share the same bolt pattern. So technically yes, you could bolt it onto the brake flange on the axle. However, your hub and drum assembly is going to have the…

view full answer...

Answer 9

The big difference between 3,000 lb axle trailer brake assemblies and 3,500 lb trailer axle brake assemblies is the width of the brake pad. The 3,500 lb kits like the #23-468-469 are 2-1/4 inches wide and the #K23-472-473-00 which fits the 3,000 lb…

view full answer...

Answer 10

Trailer brakes can be either self-adjusting like the Dexter #23-468 or may require periodic manual adjustments like #23-27, depending on the particular model assemblies you have installed on the trailer. An easy way to tell if you have self-adjusting…

view full answer...

Answer 11

Actually both of the hubs you referenced will fit and work great as a replacement for what you have on your trailer currently. Since this is a boat trailer application I'd recommend the #AKHD-545-35-G-EZ-K since it is galvanized and will fight…

view full answer...

Answer 12

The width of the #AKHD-545-35-EZ-K that you referenced that comes in at 2-1/4 inches is the width where the shoe would touch the drum. If yours overall is 2-5/8 inches including the backing plate then this is the correct fit. I attached a picture…

view full answer...