Recommended Weight Distribution System For A 9000 lb Trailer

Question

Question:

I have purchased a keystone outback travel trailer 326rl. Its weight is 8900#s. What would you recommend for a weight distribution system with sway control ?

asked by: Bill E

0

Expert Reply:

In order to determine the best weight distribution system for your towing setup, you will need to calculate the total tongue weight of your loaded ready to tow trailer and any cargo stored behind the rear axle of the tow vehicle. To do this, I suggest you consider the etrailer Tongue Weight Scale 2,000-lb Capacity # e99044. This scale will allow for an easy and accurate reading each and every time you change the tongue weight of your towing setup.

If you find your total tongue weight to be around 1,000 lbs, then I recommend the Equal-i-zer Weight Distribution System part # EQ37120ET. The Equal-i-zer is one of our most popular weight distribution systems. Featuring an integrated 4-point sway control design and adjustable shank, this system is a top-of-the-line option. Rated for tongue weight capacities up to 1,200 lbs, the spring bars can easily be changed in order to compensate for heavier loads.

Another, more economical option to consider is our Fastway e2 part # FA92-00-1200. The Fastway e2 incorporates a 2-point sway control design with built-in adjustable head. Also included is an adjustable shank, proving to be a worthy second option. As it does not include a hitch ball, I recommend part # 19286 to pair with this system.

If you find your total tongue weight to be more than 1,200 lbs but less than 1,400 lbs then I recommend the Equal-i-zer Weight Distribution System part # EQ37140ET.

I have attached a weight distribution help article and the proper way to measure your total tongue weight in addition to a review of both weight distribution systems.

expert reply by: Conner L

0

Answer 1

When it comes to a sway control bar like the #83660 Reese Friction Sway Control Kit, there is no weight rating. Since you have a trailer length of 27' the #83660 is what you are looking for. This unit dampens trailer sway caused by crosswinds…

view full answer...

Answer 2

If the trailer hitch on the motorhome has a separate capacity for use with a weight carrying hitch then you can use one. The hitch will distribute the weight from the rear of the vehicle to the front where you need it. The amount of weight…

view full answer...

Answer 3

I spoke with my contact at B and W and he informed me that the center section of the B and W Hitch part #BWHDRH25124 measures 31-13/16 inches long measured from outside of flange to outside of flange.

view full answer...

Answer 4

There are two ways to wire up two batteries. One way doubles the volts of the two batteries and the other keeps the same amount of volts. In parallel the voltage stays the same and in series it is doubled. Check out the diagram for more info.

view full answer...

Answer 5

From the top of the mounting plates to the top of the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25124 receiver is a 5-1/4" drop and then from the rearmost bolt hole to the end of the receiver is 10-7/8" (see attached).

view full answer...

Answer 6

The trailer hitches we have available for the 2014 GMC Savana Van are designed to fit the full size van model. To see if these will fit your Cutaway version, I just recommend taking a couple measurements on the vehicle's frame. The trailer hitch…

view full answer...

Answer 7

The Curt #C15320 will fit the frame of your 2014 Chevy Express Cutaway Van Chassis, but in order for the hitch to clear the bumper, the distance between the underside of the frame member that the hitch bolts to and the lowest point of the rear bumper…

view full answer...

Answer 8

Your 2012 Express Shuttle Bus would be built on the cutaway chassis version of the 2012 Express Van so that means the correct hitch you'd need is the Buyers Products part #3371801102 which was made for this style of chassis. I attached a picture…

view full answer...

Answer 9

The Draw-Tite Class III hitch you mentioned, part #41946 will fit a 2005 Chevy Express, but I couldn't say if it'll fit a motorhome on a cutaway van chassis. Usually the rear bumper structure at the rear of a motorhome is much different that…

view full answer...

Answer 10

I just went out to the warehouse and measured the Curt Trailer Hitch Receiver item #C15845. I have attached a couple of diagrams with the dimensions of this hitch on them. From the center of the back bolt to the front of the receiver is 26" The…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...