How Much Height Does Rhino-Rack Pioneer Platform # RR42114BF Add to Roof Rack

Question

Question:

Howdy. How high off the factory crossbars does the platform sit once it is mounted? Thanks.

asked by: Tim B

0

Expert Reply:

When installed the Rhino-Rack Pioneer Platform # RR42114BF that you referenced will add 1-1/2 inches to the height of your roof rack.

expert reply by: Jameson C

0

Answer 1

For your 2012 Dodge Ram 2500 with the RetraxONE ladder rack that has the t-slots for a ladder rack you'd want the Yakima Outpost HD Part #Y01153-5755 which fits the tonneau rails directly and has t-slots for a Pioneer Platform to install like the…

view full answer...

Answer 2

We have versions of the Rhino Rack Pioneer Platform that were designed for attaching to crossbars like the part #RR42114BF for a 48 by 38 inch platform or part #RR42115BF for a 58 by 47 inch platform. Both of these would attach to a Wingbar rack.

view full answer...

Answer 3

Rhino Rack states that the capacity of the Pioneer Platform Rack #RR42114BF is the weight capacity of the vehicle roof it is installed in minus the weight of the platform. The Pioneer Platform weighs 12.5 kg or 27-1/2 lbs so you'd need to…

view full answer...

Answer 4

You can connect the Rhino-Rack Pioneer Platform - Universal Mount - 48" Long x 38" Wide #RR42114BF or the larger #RR42115BF using the T-bolts. You do not need to use the universal bar clamps and will not use all of the included pieces for…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...