Does Snap Loc E-Track Fit with Other Brands of E-Track

Question

Question:

Are the Snap loc and Etrack products universal? Will a Snap lock strap fit the Etrack system?

asked by: Ryan

0

Expert Reply:

Yes, the Snap Loc E-tracks like the part # SLSS you referenced is a fit with other brands of E-track as they are all made to the same dimensions for the most part.

I attached a review video for more info for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The Erickson Horizontal E-Track, part #E19148 has 1/4 inch diameter mounting holes spaced 2 inches apart. The screws you use should be at least long enough to go 3/4 inch into the wood you are mounting the track to. The more screws you use the more…

view full answer...

Answer 2

The Camco RV Water Heater Anode Rod #CAM11563 is the anode rod we carry for Suburban water heaters. This is made of aluminum and measures 3/4 of an inch in diameter and 9-1/2 inches long. You'll need to make sure it's a match with yours.

view full answer...

Answer 3

On an 4 foot long section of E-track #EM19147 and 2 screws every 16 inches that is a total of 6 screws in the aluminum frame. This most likely will not get you near the capacity of the E-track. I recommend bolting through the aluminum frame so that…

view full answer...

Answer 4

If you're looking for wall storage, then the CargoSmart X-Track Trailer Shelf Bundle - Matte Black - Steel - 667 lbs - 5' Long #3481788-T would be the correct solution and it will give you the ability to hang some hooks; if you can locate the…

view full answer...

Answer 5

Since you are wanting the most rust proof E-Track I recommend the etrailer Horizontal E-Track - Galvanized Steel - 2,000 lbs - 4' Long #e95VR as its galvanized finish will be the best for rust prevention, and will hold up fine even though you…

view full answer...

Answer 6

That is a good question, and you will need to use three backing plates for each 5 foot section of e-track, so the exact part you will need is the following: - etrailer E-Track Backing Plates w/ Hardware - Qty 3 #e46RR These will fit perfectly with…

view full answer...

Answer 7

We do recommend backing plates for all e-track installations. They will provide additional support. You will need a set of four backing plates, part #e66RR, for an 8' section of E-Track. I have included a product description link, a weblink on…

view full answer...

Answer 8

When securing your motorcycle inside your enclosed 12 foot long trailer using a chock like the Tow-Rax #TWSPWM the most important factor to consider is the trailer's tongue weight. You will just want to make sure that its tongue weight with the…

view full answer...

Answer 9

Yes, you can drill holes to add an A-frame jack to your pop-up camper if your current jack is getting in the way of your anti-sway bars. You will need to have a mounting plate to of some sort to drill into as opposed to drilling into the frame of…

view full answer...

Answer 10

Snap-Loc recommends using a 5/16 inch carriage bolt to install the e-track tie down. You will need bolts of sufficient length to go through the plywood and the aluminum frame members. Using galvanized hardware would be acceptable, but stainless would…

view full answer...

Answer 11

The Snap-Loc E-Track Tie-Down Anchor #SLSS will have the same break strength and safe working load limit no matter what the orientation is when installed. The maximum load (break strength) is 3,000 lbs and the safe working load limit is 1,000 lbs.…

view full answer...

Answer 12

Yes, the CargoSmart Rope Ring part #3481767 is compatible with the Snap-Loc E-Track Tie-Down Anchor part #SLSS. The safe working load limit of the Snap-Loc E-Track Tie-Down Anchor is 1,000 lbs even if you use the 2,000 lb CargoSmart Rope Ring you…

view full answer...

Does Snap Loc E-Track Fit with Other Brands of E-Track

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching