What Spindle Does 7k Trailer Hub # AKHD-865-7-2-EZ-K Fit

Question

Question:

I have 2 sets of hubs one is part number AKHD-865-7-2-EZ-K and the other is AKLHUB-865-7-2-K. What is the part number for the spindles I need to fit these hubs.

asked by: Tony W

0

Expert Reply:

The spindle your hubs # AKHD-865-7-2-EZ-K and # AKHD-865-7-2-K are designed to fit are the number 42 spindle like the part # TRU37FR.

expert reply by: Jameson C

0

Answer 1

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 4

Hello Jeffrey, While I'm sure we have a bearing kit for your car trailer, we don't have any way of knowing off-hand or cross-referencing what bearings you need. You mentioned you have them out, so you should be able to see the part…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 6

I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Yes, the bearing kit part #BK3-210 does fit a good portion of the 7,000 lb Dexter axles out there, but some of the 7k Dexter axles require a slightly larger grease seal which instead requires the kit part #BK3-200. What you'll want to do is…

view full answer...

Answer 9

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643…

view full answer...

Answer 10

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard…

view full answer...

Answer 11

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 12

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to…

view full answer...

What Spindle Does 7k Trailer Hub # AKHD-865-7-2-EZ-K Fit

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching